Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Help
Enclosure Design & Construction
Building In-Trunk: Tips and Tricks
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="GCAdidas13" data-source="post: 831205" data-attributes="member: 557864"><p>ah, well i thought pretty well about this</p><p></p><p>i think the best bet is to situate the box as far forward as you can, and then glue some fleece to the baffle, leaving a lot of room on the outsides to stretch, then you can stretch the fleece to the edges of the trunk.</p><p></p><p>if temporary, you can use hot glue to glue the fleece to tape. if permanant, go ahead and glue right to the side wall or lip of the trunk-to-cabin hole.</p><p></p><p>after your glue all dries, pour resin and hardener all over all the fleece you just glassed. you might want to do both sides, but that's your call. from there, trim out your port(s) and mounting holes(s), and you're set.</p><p></p><p>if temporary, you should take the parts that are on the side wall and/or lip, and use a sort of temporary caulking (something that is not too adhesive) and make it air-tight.</p><p></p><p>any more questions, just ask //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif</p></blockquote><p></p>
[QUOTE="GCAdidas13, post: 831205, member: 557864"] ah, well i thought pretty well about this i think the best bet is to situate the box as far forward as you can, and then glue some fleece to the baffle, leaving a lot of room on the outsides to stretch, then you can stretch the fleece to the edges of the trunk. if temporary, you can use hot glue to glue the fleece to tape. if permanant, go ahead and glue right to the side wall or lip of the trunk-to-cabin hole. after your glue all dries, pour resin and hardener all over all the fleece you just glassed. you might want to do both sides, but that's your call. from there, trim out your port(s) and mounting holes(s), and you're set. if temporary, you should take the parts that are on the side wall and/or lip, and use a sort of temporary caulking (something that is not too adhesive) and make it air-tight. any more questions, just ask [IMG]//content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif[/IMG] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Enclosure Design & Construction
Building In-Trunk: Tips and Tricks
Top
Menu
What's new
Forum list