Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Enclosure Design & Construction
Building a ported box for my 2 x SA-10-d4's
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="ecxtimmy" data-source="post: 8056209" data-attributes="member: 638814"><p>I have a few quick question about the sub box that I am going to be building.</p><p></p><p>First I have two SA-10 D4's wired down to 1Ohm, being powered by a SAZ-1500V3, currently have a crappy prefab enclosure. Though the subs still sound great I know they can be much louder.</p><p></p><p>I have used a few online calculators as well as design software to build a basic ported box. I just want to verify that the box design I have will be sufficient.</p><p></p><p>I've been playing with some numbers and I'm curious about port recommendations as far as width and length</p><p></p><p>Current Box design is a simple ported box with a side slot vent, subs are sharing air space. I'm using RE audio Box calculator</p><p></p><p>specs are</p><p></p><p>Width - 36"</p><p></p><p>Depth (top and bottom) - 12"</p><p></p><p>Height - 15"</p><p></p><p>Square port width - 2"</p><p></p><p>Square port length - 6"</p><p></p><p>Box volume comes to - 2.53 ft^3</p><p></p><p>Tuned frequency - 35.15</p><p></p><p>Just want some advice or confirmation that my box design will suite my setup</p><p></p><p>Thanks,</p><p></p><p>Brandon</p></blockquote><p></p>
[QUOTE="ecxtimmy, post: 8056209, member: 638814"] I have a few quick question about the sub box that I am going to be building. First I have two SA-10 D4's wired down to 1Ohm, being powered by a SAZ-1500V3, currently have a crappy prefab enclosure. Though the subs still sound great I know they can be much louder. I have used a few online calculators as well as design software to build a basic ported box. I just want to verify that the box design I have will be sufficient. I've been playing with some numbers and I'm curious about port recommendations as far as width and length Current Box design is a simple ported box with a side slot vent, subs are sharing air space. I'm using RE audio Box calculator specs are Width - 36" Depth (top and bottom) - 12" Height - 15" Square port width - 2" Square port length - 6" Box volume comes to - 2.53 ft^3 Tuned frequency - 35.15 Just want some advice or confirmation that my box design will suite my setup Thanks, Brandon [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Enclosure Design & Construction
Building a ported box for my 2 x SA-10-d4's
Top
Menu
Home
Refresh