Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
Car Audio Build Logs
Bronco Utopia Build - New DIYer
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="DeeEye Why" data-source="post: 8835842" data-attributes="member: 688535"><p>Looking to step up the audio on a new bronco. Have had some high end installs done in the past, but after seeing what some of these “professionals” do I’m leaning towards installing myself as my OCD and I can give it the time/attention it deserves to be a clean install with clean wiring and labels.</p><p></p><p>But - I’m very new to car audio DIY, so will likely need some assistance along the way. Feel free to tell me I’m being an idiot; I just ask that you also offer suggestions/explanations in addition to any hurled expletives.</p><p></p><p>Let’s start off with the gear I’m planning on using</p><p></p><p>Planned Gear -</p><p></p><p>SUBS - 2 Utopia 10WM - open to alternatives/suggestions; I’ve had these in the past and was happy with their performance</p><p></p><p>FRONT</p><p></p><ul> <li data-xf-list-type="ul">Replace the factory dash 4” with Utopia 3.5WMs</li> <li data-xf-list-type="ul">Either Focal 165W-XP component kit with the 6.5 in kick panels and tweets mounting TBD run active OR</li> <li data-xf-list-type="ul">Utopia 6WMs in kick panels and TBM tweets mounting TBD</li> <li data-xf-list-type="ul">Thinking about changing the center to a 3.5WM</li> </ul><p>AMPS</p><p></p><ul> <li data-xf-list-type="ul">Helix V8 DSP MKII<ul> <li data-xf-list-type="ul">This should be able to drive all the front speakers - my only concern here is the 6WMs. The 4 ohm power per channel is rated at 75 watts per channel, but the 6WM is good to 100. I’ve also heard that this amp can send more power to channels from the underutilized channels? Just want to make sure this is enough juice for the fronts.</li> <li data-xf-list-type="ul">Also I’d like to either keep the stock rear speakers or replace them with something slightly better, but really just run them as rear fill - Assuming I wanted to power those from this amp could I use a single channel for the rear fill since I’d only have one channel left? If I can't do this I'll probably just start with the front stage for now.</li> </ul></li> <li data-xf-list-type="ul">Helix M ONE X<ul> <li data-xf-list-type="ul">I’m assuming this should be able to power the 2 WM10s if wired in this configuration: <a href="https://images.crutchfieldonline.com/ca/learningcenter/car/subwoofer_wiring/2-DVC-4-ohm-mono-low-imp.jpg" target="_blank">https://images.crutchfieldonline.com/ca/learningcenter/car/subwoofer_wiring/2-DVC-4-ohm-mono-low-imp.jpg</a> but I don’t know how wiring like this impacts the math… The stated RMS for the subs is 400 watts, and I’m assuming wiring like this would allow the 1-ohm power from the amp at 1030 watts?</li> </ul></li> </ul><p>After this gets sorted I’ll move on to figuring out the necessary wiring for power/ground/speakers. Really appreciate any assistance.</p></blockquote><p></p>
[QUOTE="DeeEye Why, post: 8835842, member: 688535"] Looking to step up the audio on a new bronco. Have had some high end installs done in the past, but after seeing what some of these “professionals” do I’m leaning towards installing myself as my OCD and I can give it the time/attention it deserves to be a clean install with clean wiring and labels. But - I’m very new to car audio DIY, so will likely need some assistance along the way. Feel free to tell me I’m being an idiot; I just ask that you also offer suggestions/explanations in addition to any hurled expletives. Let’s start off with the gear I’m planning on using Planned Gear - SUBS - 2 Utopia 10WM - open to alternatives/suggestions; I’ve had these in the past and was happy with their performance FRONT [LIST] [*]Replace the factory dash 4” with Utopia 3.5WMs [*]Either Focal 165W-XP component kit with the 6.5 in kick panels and tweets mounting TBD run active OR [*]Utopia 6WMs in kick panels and TBM tweets mounting TBD [*]Thinking about changing the center to a 3.5WM [/LIST] AMPS [LIST] [*]Helix V8 DSP MKII [LIST] [*]This should be able to drive all the front speakers - my only concern here is the 6WMs. The 4 ohm power per channel is rated at 75 watts per channel, but the 6WM is good to 100. I’ve also heard that this amp can send more power to channels from the underutilized channels? Just want to make sure this is enough juice for the fronts. [*]Also I’d like to either keep the stock rear speakers or replace them with something slightly better, but really just run them as rear fill - Assuming I wanted to power those from this amp could I use a single channel for the rear fill since I’d only have one channel left? If I can't do this I'll probably just start with the front stage for now. [/LIST] [*]Helix M ONE X [LIST] [*]I’m assuming this should be able to power the 2 WM10s if wired in this configuration: [URL]https://images.crutchfieldonline.com/ca/learningcenter/car/subwoofer_wiring/2-DVC-4-ohm-mono-low-imp.jpg[/URL] but I don’t know how wiring like this impacts the math… The stated RMS for the subs is 400 watts, and I’m assuming wiring like this would allow the 1-ohm power from the amp at 1030 watts? [/LIST] [/LIST] After this gets sorted I’ll move on to figuring out the necessary wiring for power/ground/speakers. Really appreciate any assistance. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Car Audio Build Logs
Bronco Utopia Build - New DIYer
Top
Menu
Home
Refresh