Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
General Car Audio
Bridged mode keeps cutting off...no fuses blown
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="31337hxr" data-source="post: 23074" data-attributes="member: 541111"><p>The amplifier is a Sony XM-1502 760watt amplifier and the two subwoofers are the Infinity kappe perfect 12.1 Single voice coil 4-ohm subwoofer.</p><p></p><p>The subs are BRIDGED. Positive of both speakers are connected to the positive terminal of the R side of the amp, and the negatives of both speakers are connected to the NEGATIVE on the Left channel of the amp.</p><p></p><p>thus, when the volume increases, the over-current light comes on.</p><p></p><p>this amp is suppose to do the following specs:</p><p></p><p>760W max power (380W x2 @2O )</p><p></p><p>150W x2 into 4O , 20-20kHz, at 0.04% THD</p><p></p><p>190W x2 into 2O , 20-20kHz, at 0.01% THD</p><p></p><p>380W x1 into 4O , 20-20kHz, at 0.01% THD</p><p></p><p>So actually, i'm trying to push 380 watts into both subs simultaneously! The types of amp wiring cable i'm using are:</p><p></p><p>1 RCA Interconnect high definition audio cable shielded w/Built in remote wire 25ft Right Angle</p><p></p><p>2 Red Power Wire 20ft 4Gauge</p><p></p><p>3 Blue/Purple Ground Wire 4ft 4Gauge</p><p></p><p>4 OFC Speaker Cable 35ft 12Gauge</p><p></p><p>5 Blue remote turn on wire 20ft 16Gauge</p><p></p><p>6 Water Resistant Inline Fuse Holder AGU type 4Gauge</p><p></p><p>7 Agu Fuse 80Amp Gold plated</p><p></p><p>8 Gold ring terminal 1 4Gauge</p><p></p><p>9 Split loom for cable protection and organization 6ft 4Guage</p><p></p><p>Black Color</p><p></p><p>also using 40 amp fuse for battery and 40 amp fuse for amplifier.</p><p></p><p>my head unit is a pioneer deh-p4400 but i guess that doesn't matter. the subs and amp works fine in 2 channel mode but it's less power.</p><p></p><p>Hope this help! thanks</p></blockquote><p></p>
[QUOTE="31337hxr, post: 23074, member: 541111"] The amplifier is a Sony XM-1502 760watt amplifier and the two subwoofers are the Infinity kappe perfect 12.1 Single voice coil 4-ohm subwoofer. The subs are BRIDGED. Positive of both speakers are connected to the positive terminal of the R side of the amp, and the negatives of both speakers are connected to the NEGATIVE on the Left channel of the amp. thus, when the volume increases, the over-current light comes on. this amp is suppose to do the following specs: 760W max power (380W x2 @2O ) 150W x2 into 4O , 20-20kHz, at 0.04% THD 190W x2 into 2O , 20-20kHz, at 0.01% THD 380W x1 into 4O , 20-20kHz, at 0.01% THD So actually, i'm trying to push 380 watts into both subs simultaneously! The types of amp wiring cable i'm using are: 1 RCA Interconnect high definition audio cable shielded w/Built in remote wire 25ft Right Angle 2 Red Power Wire 20ft 4Gauge 3 Blue/Purple Ground Wire 4ft 4Gauge 4 OFC Speaker Cable 35ft 12Gauge 5 Blue remote turn on wire 20ft 16Gauge 6 Water Resistant Inline Fuse Holder AGU type 4Gauge 7 Agu Fuse 80Amp Gold plated 8 Gold ring terminal 1 4Gauge 9 Split loom for cable protection and organization 6ft 4Guage Black Color also using 40 amp fuse for battery and 40 amp fuse for amplifier. my head unit is a pioneer deh-p4400 but i guess that doesn't matter. the subs and amp works fine in 2 channel mode but it's less power. Hope this help! thanks [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
General Car Audio
Bridged mode keeps cutting off...no fuses blown
Top
Menu
Home
Refresh