Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
Car Audio Build Logs
Box build for Ravens9322
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="PV Audio" data-source="post: 4453376" data-attributes="member: 554493"><p>Enclosure looks great, paintjob looks like ****. If you're offended by that, don't be, because I've painted some of the most hideous looking **** ever, so take my advice on painting (I'll have pics tomorrow once I clearcoat my rear channels). There are 4 main steps to a good paintjob, plus the secret detail;</p><p></p><p>1. Sand the enclosure four times: 60 grit, 150 grit, 220 grit, 320 grit. This helps to knock down almost all the imperfections and helps seal up the end grain a little bit.</p><p></p><p>2. Seal the enclosure using a sealant of your choice, whether it be shellac, glue-wash, fiberglass or sanding sealer. Make sure you spend good time on this step, and sand in between each coat after the first two. Go to increasing grits from 320 up to 400.</p><p></p><p>3. Bondo all edges, joints, screw holes and flaws. Make sure and be very thorough when doing this, because endgrain can swell when sealing and shows very easily. Most likely the most frustrating thing ever. Make sure you sand down the bondo first with 220 grit, then 320. Should repeat twice to remove pin holes after the first go around.</p><p></p><p>4. Prime using automotive primer or other fast drying primer. Two coats, one on top of the other, very thin. That's the key to successful painting, getting a GLASS smooth primer base that is thick enough to dry sand with 320 to remove most imperfections. Dry sand the first two coats with 320, apply another coat and wet sand with 600, then another coat and wetsand with 800 or 1500. Enclosure should literally feel like glass.</p><p></p><p>From there, use the top coat of your choice, but keep in mind to do steady, even strokes and do many thin coats instead of few thick coats. You get less runs and the finish looks more even in the end.</p><p></p><p>The secret detail? It takes a lot of time to get a paint finish looking good. Even if you spend hours, the smallest things show up and make you frustrated. Don't rush it, just keep going at it. You shouldn't be able to sand, seal, prime and paint an enclosure in the course of a day if you take your time, as it takes a few hours to be able to fully dry sand primer anyway.</p><p></p><p>Keep up the good work. //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif</p></blockquote><p></p>
[QUOTE="PV Audio, post: 4453376, member: 554493"] Enclosure looks great, paintjob looks like ****. If you're offended by that, don't be, because I've painted some of the most hideous looking **** ever, so take my advice on painting (I'll have pics tomorrow once I clearcoat my rear channels). There are 4 main steps to a good paintjob, plus the secret detail; 1. Sand the enclosure four times: 60 grit, 150 grit, 220 grit, 320 grit. This helps to knock down almost all the imperfections and helps seal up the end grain a little bit. 2. Seal the enclosure using a sealant of your choice, whether it be shellac, glue-wash, fiberglass or sanding sealer. Make sure you spend good time on this step, and sand in between each coat after the first two. Go to increasing grits from 320 up to 400. 3. Bondo all edges, joints, screw holes and flaws. Make sure and be very thorough when doing this, because endgrain can swell when sealing and shows very easily. Most likely the most frustrating thing ever. Make sure you sand down the bondo first with 220 grit, then 320. Should repeat twice to remove pin holes after the first go around. 4. Prime using automotive primer or other fast drying primer. Two coats, one on top of the other, very thin. That's the key to successful painting, getting a GLASS smooth primer base that is thick enough to dry sand with 320 to remove most imperfections. Dry sand the first two coats with 320, apply another coat and wet sand with 600, then another coat and wetsand with 800 or 1500. Enclosure should literally feel like glass. From there, use the top coat of your choice, but keep in mind to do steady, even strokes and do many thin coats instead of few thick coats. You get less runs and the finish looks more even in the end. The secret detail? It takes a lot of time to get a paint finish looking good. Even if you spend hours, the smallest things show up and make you frustrated. Don't rush it, just keep going at it. You shouldn't be able to sand, seal, prime and paint an enclosure in the course of a day if you take your time, as it takes a few hours to be able to fully dry sand primer anyway. Keep up the good work. [IMG]//content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif[/IMG] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Car Audio Build Logs
Box build for Ravens9322
Top
Menu
Home
Refresh