Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Discussion
Speakers
Boston Acoustic Z6
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="HERETIC" data-source="post: 866590" data-attributes="member: 560671"><p>would it be stupid to bridge my dls A3 to power those cdt's i got?</p><p></p><p>ULTIMATE series A3 is a two-channel amplifier rated at 2 x 100 Watts. A true, dual mono block with separate power sources that provides typical output of 2 x 150 Watts with 4 ohm stereo and 550/870 Watts with 4/2 ohm mono.</p><p></p><p>Built-in fan control. Built-in, variable 50-125 Hz switchable low-pass filter for subwoofers. Built-in variable 20-200 Hz. high-pass filter that can be used as a subsonic filter or high-pass filter for front systems. Dual power terminals where you can connect dual power feeds or a DLS Power Cap. Button for switching phases when you use it as a subwoofer amplifier.</p><p></p><p>RMS output per channel at 13,8 volts, 20 Hz - 20 kHz ,</p><p></p><p>Mode : AB</p><p></p><p>Number of channels : 2</p><p></p><p>Nominal power in 4 ohm : 2 x 100 Watt</p><p></p><p>Typical power in 4 ohm : 2 x 150 watt</p><p></p><p>Typical power in 2 ohm : 2 x 270 Watt</p><p></p><p>Typical power in 1 ohm : 2 x 425 Watt</p><p></p><p>Typical power in 4 ohm bridge mode : 550 Watt</p><p></p><p>Typical power in 2 ohm bridge mode : 870 Watt</p><p></p><p>Typical power in 1,33 ohm bridge mode : 1000 watt</p><p></p><p>S / N ratio, A-weighted : &gt; 100 dB</p><p></p><p>Damping factor : &gt; 200</p><p></p><p>Input impedance : &gt; 10 kohm</p><p></p><p>Input sensitivity, variable : 0,2 - 7 V</p><p></p><p>Filter, highpass, variable : 20 - 200 Hz</p><p></p><p>Filter lowpass, variable : 50-125 Hz</p><p></p><p>Terminal for external cooling fan : Yes</p><p></p><p>Double DC-inputs : Yes</p><p></p><p>Phase shift button : Yes</p><p></p><p>Current draw, idle : 1,1 A</p><p></p><p>Current draw, maximum : 140 A</p><p></p><p>Dimensions W x D x H : 410 x 240 x 73 mm (16,15 x 9,45 x 2,87 inch)</p></blockquote><p></p>
[QUOTE="HERETIC, post: 866590, member: 560671"] would it be stupid to bridge my dls A3 to power those cdt's i got? ULTIMATE series A3 is a two-channel amplifier rated at 2 x 100 Watts. A true, dual mono block with separate power sources that provides typical output of 2 x 150 Watts with 4 ohm stereo and 550/870 Watts with 4/2 ohm mono. Built-in fan control. Built-in, variable 50-125 Hz switchable low-pass filter for subwoofers. Built-in variable 20-200 Hz. high-pass filter that can be used as a subsonic filter or high-pass filter for front systems. Dual power terminals where you can connect dual power feeds or a DLS Power Cap. Button for switching phases when you use it as a subwoofer amplifier. RMS output per channel at 13,8 volts, 20 Hz - 20 kHz , Mode : AB Number of channels : 2 Nominal power in 4 ohm : 2 x 100 Watt Typical power in 4 ohm : 2 x 150 watt Typical power in 2 ohm : 2 x 270 Watt Typical power in 1 ohm : 2 x 425 Watt Typical power in 4 ohm bridge mode : 550 Watt Typical power in 2 ohm bridge mode : 870 Watt Typical power in 1,33 ohm bridge mode : 1000 watt S / N ratio, A-weighted : > 100 dB Damping factor : > 200 Input impedance : > 10 kohm Input sensitivity, variable : 0,2 - 7 V Filter, highpass, variable : 20 - 200 Hz Filter lowpass, variable : 50-125 Hz Terminal for external cooling fan : Yes Double DC-inputs : Yes Phase shift button : Yes Current draw, idle : 1,1 A Current draw, maximum : 140 A Dimensions W x D x H : 410 x 240 x 73 mm (16,15 x 9,45 x 2,87 inch) [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Speakers
Boston Acoustic Z6
Top
Menu
What's new
Forum list
