Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
biamp or bridge?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="jt34237" data-source="post: 7138323" data-attributes="member: 621608"><p>What would you do if this was your setup? It seems that with the bridged option I would get more power which is ultimately what I want. I wasn't sure if there was a benefit to biamping. The biamping option would only give the woofers the 150 rms that the specs sheet lists as the "continous rated power" but I KNOW these speakers can take more which is why I would lean more toward the bridging option. What do you guys think? I have listed the specs below for the amp, the woofer, and the tweeter. Thanks.</p><p></p><p>JL HD600/4 Amplifier</p><p></p><p>150 x 4 @ 4 ohms</p><p></p><p>300 x 2 @ 4 ohms bridged</p><p></p><p>Hertz MLK 165 Component Set</p><p></p><p>The specs for the mlk 165 woofer are as follows:</p><p></p><p>Size <strong>ML 165 Woofer</strong> (6”1/2)</p><p></p><p>Power peak300</p><p></p><p>Handling cont. program150</p><p></p><p>(Watt)</p><p></p><p>Impedance Ω 4</p><p></p><p>Frequency Hz35 ÷25k</p><p></p><p>The specs for the MLK 165 tweeter are as follows:</p><p></p><p>•(mm) <strong>ML 28 Tweeter28</strong> (1”1/8)</p><p></p><p>•180 Watt</p><p></p><p>•Fs: 920 Hz</p><p></p><p>•91dB/SPL</p><p></p><p>•4 Ohm</p><p></p><p>Thank you for your help and Merry Christmas!</p></blockquote><p></p>
[QUOTE="jt34237, post: 7138323, member: 621608"] What would you do if this was your setup? It seems that with the bridged option I would get more power which is ultimately what I want. I wasn't sure if there was a benefit to biamping. The biamping option would only give the woofers the 150 rms that the specs sheet lists as the "continous rated power" but I KNOW these speakers can take more which is why I would lean more toward the bridging option. What do you guys think? I have listed the specs below for the amp, the woofer, and the tweeter. Thanks. JL HD600/4 Amplifier 150 x 4 @ 4 ohms 300 x 2 @ 4 ohms bridged Hertz MLK 165 Component Set The specs for the mlk 165 woofer are as follows: Size [B]ML 165 Woofer[/B] (6”1/2) Power peak300 Handling cont. program150 (Watt) Impedance Ω 4 Frequency Hz35 ÷25k The specs for the MLK 165 tweeter are as follows: •(mm) [B]ML 28 Tweeter28[/B] (1”1/8) •180 Watt •Fs: 920 Hz •91dB/SPL •4 Ohm Thank you for your help and Merry Christmas! [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
biamp or bridge?
Top
Menu
What's new
Forum list