Reply to thread

Message

<blockquote data-quote="RoLLaxPhile" data-source="post: 2532850" data-attributes="member: 572952">Okay I&#039;ve read every sticky on this forum including the amplifiers, gains, setting tuturials, etc.I have a Soundstream Van Gogh 1600.2 amp...capable of400x2 4ohms800x2 2ohms1600x1 bridged 4ohms monomy question after reading amplifier setting tutorial, Is it possible for me to run my VGA to my front components without actually blowing it?Hertz HSK 165 L125watts RMS 4ohms250watts PEAK 4ohmsIf i set the gains real low and according to this table chart i got from the amp setting tutorial stickyTable:50 Watts -- 1.0 Ohms, V=7.07 -- 2.0 Ohms, V=10.0 -- 4.0 Ohms, V=14.14 -- 8.0 Ohms, V=20.0100 Watts -- 1.0 Ohms, V=10.0 -- 2.0 Ohms, V=14.14 -- 4.0 Ohms, V=20.0 -- 8.0 Ohms, V=28.28150 Watts -- 1.0 Ohms, V=12.24 -- 2.0 Ohms, V=17.32 -- 4.0 Ohms, V=24.49 -- 8.0 Ohms, V=34.64200 Watts -- 1.0 Ohms, V=14.14 -- 2.0 Ohms, V=20.0 -- 4.0 Ohms, V=28.28 -- 8.0 Ohms, V=40.0I can get the recommended wattage without going over the peak limit of my components thus not blowing them at all...Any one with experience or educated opinions let me know...And I have read everything here so I&#039;m just trying to better understand amps and their limitsby the way my amp puts out 26.6V at max setting using the digital multimeter</blockquote>

[QUOTE="RoLLaxPhile, post: 2532850, member: 572952"] Okay I've read every sticky on this forum including the amplifiers, gains, setting tuturials, etc. I have a Soundstream Van Gogh 1600.2 amp...capable of 400x2 4ohms 800x2 2ohms 1600x1 bridged 4ohms mono my question after reading amplifier setting tutorial, Is it possible for me to run my VGA to my front components without actually blowing it? Hertz HSK 165 L 125watts RMS 4ohms 250watts PEAK 4ohms If i set the gains real low and according to this table chart i got from the amp setting tutorial sticky Table:50 Watts -- 1.0 Ohms, V=7.07 -- 2.0 Ohms, V=10.0 -- 4.0 Ohms, V=14.14 -- 8.0 Ohms, V=20.0 100 Watts -- 1.0 Ohms, V=10.0 -- 2.0 Ohms, V=14.14 -- 4.0 Ohms, V=20.0 -- 8.0 Ohms, V=28.28 [B]150 Watts -- 1.0 Ohms, V=12.24 -- 2.0 Ohms, V=17.32 -- [/B][B][I]4.0 Ohms[/I][/B][B][I], V=24.49 [/I][/B][B]-- 8.0 Ohms, V=34.64[/B] 200 Watts -- 1.0 Ohms, V=14.14 -- 2.0 Ohms, V=20.0 -- 4.0 Ohms, V=28.28 -- 8.0 Ohms, V=40.0 I can get the recommended wattage without going over the peak limit of my components thus not blowing them at all... Any one with experience or educated opinions let me know...And I have read everything here so I'm just trying to better understand amps and their limits by the way my amp puts out 26.6V at max setting using the digital multimeter [/QUOTE]

Verification