Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Discussion
General Car Audio
Audiobahn
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Ed Lester" data-source="post: 4588348" data-attributes="member: 587479"><p>We ran the HC2400s before. I did manage to get 1800w out of one. It was the flame amp. Very inefficient. about 55%, It was a current hog. You can measure efficiency very easily.</p><p></p><p>At full power play a test tone. 60hz will do. Measure the DC voltage on the input and also measure the DC current draw on the power input. Multiply these numbers and it will tell you the wattage input.</p><p></p><p>If I remember correctly the 2400 we tested had a voltage drop from 14.2 volt to 12.5 volts. So we use the 12.5v and multiply by the current draw which was like 260-265 amps. This gave us 3,312.5 watts of input.</p><p></p><p>Now we measure the output. Measure voltage and current on the AC output to the speakers.</p><p></p><p>I think we measured about 75volts AC and 24 amps output or so. This gave us about 1800w. and thats not even the RMS which would be about 1,272 watts because we multiply 1800 by the root mean square of .707.</p><p></p><p>Now 1800 is about 54-55% of 3,312.5</p><p></p><p>Not very good at all.</p></blockquote><p></p>
[QUOTE="Ed Lester, post: 4588348, member: 587479"] We ran the HC2400s before. I did manage to get 1800w out of one. It was the flame amp. Very inefficient. about 55%, It was a current hog. You can measure efficiency very easily. At full power play a test tone. 60hz will do. Measure the DC voltage on the input and also measure the DC current draw on the power input. Multiply these numbers and it will tell you the wattage input. If I remember correctly the 2400 we tested had a voltage drop from 14.2 volt to 12.5 volts. So we use the 12.5v and multiply by the current draw which was like 260-265 amps. This gave us 3,312.5 watts of input. Now we measure the output. Measure voltage and current on the AC output to the speakers. I think we measured about 75volts AC and 24 amps output or so. This gave us about 1800w. and thats not even the RMS which would be about 1,272 watts because we multiply 1800 by the root mean square of .707. Now 1800 is about 54-55% of 3,312.5 Not very good at all. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
General Car Audio
Audiobahn
Top
Menu
What's new
Forum list