Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Amp/Speaker Config help please???
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="wakedreams3" data-source="post: 8714377" data-attributes="member: 680765"><p>All,</p><p></p><p>I have a Kicker ZX250.2 amp powering 4 - KM620.2 drivers with seperate tweeters. (If you count the drivers and tweeters there are effectively 8 speakers) Essentially the original install has 2 speakers going to each channel of the amp. </p><p></p><p>My amp continues to clip out (protection light comes on and kills amp). I have checked voltage at the amp terminals on the Remote Wire and B+…voltage remains high before and after amp turns off (protection light on). </p><p></p><p>I assume my amp cutting out is because on the speakers it is trying to power?? My thought is upgrade to a 4 channel amp unless I am on the wrong path? </p><p></p><p>Here are the speaker/tweeter specs:</p><p></p><p><u>General</u></p><p>Design 2-way</p><p>Tweeter Design 3/4" Dome</p><p>Tweeter Composition Titanium</p><p>Woofer Composition Injection molded poly</p><p>Woofer Surround Santoprene rubber</p><p></p><p><u>Specifications</u></p><p>Sensitivity 88 dB</p><p>Frequency Response 35 - 21k Hz</p><p>RMS Power Range (Watts) 10-65</p><p>Peak Power Handling (Watts) 195</p><p>Impedance (Ohms) 4</p><p>Top-mount Depth (Inches) 2 13/16</p><p>Bottom-mount Depth (Inches) N/A</p><p>Cutout Diameter or Length (inches) 5 1/8</p></blockquote><p></p>
[QUOTE="wakedreams3, post: 8714377, member: 680765"] All, I have a Kicker ZX250.2 amp powering 4 - KM620.2 drivers with seperate tweeters. (If you count the drivers and tweeters there are effectively 8 speakers) Essentially the original install has 2 speakers going to each channel of the amp. My amp continues to clip out (protection light comes on and kills amp). I have checked voltage at the amp terminals on the Remote Wire and B+…voltage remains high before and after amp turns off (protection light on). I assume my amp cutting out is because on the speakers it is trying to power?? My thought is upgrade to a 4 channel amp unless I am on the wrong path? Here are the speaker/tweeter specs: [U]General[/U] Design 2-way Tweeter Design 3/4" Dome Tweeter Composition Titanium Woofer Composition Injection molded poly Woofer Surround Santoprene rubber [U]Specifications[/U] Sensitivity 88 dB Frequency Response 35 - 21k Hz RMS Power Range (Watts) 10-65 Peak Power Handling (Watts) 195 Impedance (Ohms) 4 Top-mount Depth (Inches) 2 13/16 Bottom-mount Depth (Inches) N/A Cutout Diameter or Length (inches) 5 1/8 [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Amp/Speaker Config help please???
Top
Menu
Home
Refresh