Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Equipment
Amplifiers
Amp in power protect
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="2RZ-FE" data-source="post: 8667016" data-attributes="member: 631274"><p>I ordered a new fuse holder for under the hood. <a href="http://www.knukonceptz.com/mobile-audio/inline-fuse-holders/sp/in-line-waterproof-mini-anl-fuse-holder/" target="_blank">http://www.knukonceptz.com/mobile-audio/inline-fuse-holders/sp/in-line-waterproof-mini-anl-fuse-holder/</a>. This will have a 120A fuse.</p><p></p><p>The RF P300x2 amp has no onboard fuse so will be using one side of this. <a href="http://www.knukonceptz.com/mobile-audio/distribution-fuse-blocks/sp/bassik-2-way-4-gauge-fuse-distribution-block/" target="_blank">http://www.knukonceptz.com/mobile-audio/distribution-fuse-blocks/sp/bassik-2-way-4-gauge-fuse-distribution-block/</a>. It will have a 50 amp fuse. </p><p></p><p>My JBL GTR-1001 has onboard fuses so won't run an inline fuse. It says to use a 105 amp fuse at the battery but I'm being conservative on the gain running it at 2 ohm so treating the amp like its a GTR-601 or running it at 4 ohm so a 70 amp fuse will do. </p><p></p><p>Bought extra fuses.</p><p></p><p>The bottom of the seat comes out just by pushing back and pulling up at the front. </p><p></p><p>I have the power wire running down the drivers side and running through the middle as it enters the trunk. My ground point currently is in the middle of the angled metal near the seat back between the floor and the trunk. May change it depending on where I rearrange the amps. </p><p></p><p>RCA's are down the middle but away from the power. Speaker wires are down the sides away from the power wire. </p><p></p><p>Now I need to decide if I really need the relay for two amp turn on or not. I will see how it goes without it.</p><p></p><p>Will look into the wire loom.</p></blockquote><p></p>
[QUOTE="2RZ-FE, post: 8667016, member: 631274"] I ordered a new fuse holder for under the hood. [URL="http://www.knukonceptz.com/mobile-audio/inline-fuse-holders/sp/in-line-waterproof-mini-anl-fuse-holder/"]http://www.knukonceptz.com/mobile-audio/inline-fuse-holders/sp/in-line-waterproof-mini-anl-fuse-holder/[/URL]. This will have a 120A fuse. The RF P300x2 amp has no onboard fuse so will be using one side of this. [URL="http://www.knukonceptz.com/mobile-audio/distribution-fuse-blocks/sp/bassik-2-way-4-gauge-fuse-distribution-block/"]http://www.knukonceptz.com/mobile-audio/distribution-fuse-blocks/sp/bassik-2-way-4-gauge-fuse-distribution-block/[/URL]. It will have a 50 amp fuse. My JBL GTR-1001 has onboard fuses so won't run an inline fuse. It says to use a 105 amp fuse at the battery but I'm being conservative on the gain running it at 2 ohm so treating the amp like its a GTR-601 or running it at 4 ohm so a 70 amp fuse will do. Bought extra fuses. The bottom of the seat comes out just by pushing back and pulling up at the front. I have the power wire running down the drivers side and running through the middle as it enters the trunk. My ground point currently is in the middle of the angled metal near the seat back between the floor and the trunk. May change it depending on where I rearrange the amps. RCA's are down the middle but away from the power. Speaker wires are down the sides away from the power wire. Now I need to decide if I really need the relay for two amp turn on or not. I will see how it goes without it. Will look into the wire loom. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Equipment
Amplifiers
Amp in power protect
Top
Menu
Home
Refresh