Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Discussion
General Car Audio
Adding amp using existing oem speaker wiring
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Old_Slapper" data-source="post: 8880438" data-attributes="member: 690458"><p>1. You can run speakers from the aftermarket amp to the factory amp. From there, you can tap into the factory speaker wires that go to the speakers.</p><p></p><p>2. Always go off the RCA outputs of an aftermarket radio. The LOC's have a tendency to filter out some tones.</p><p></p><p>3. Your 3.5" speakers will handle less power and a higher frequency than the 6x9s. You can use a 4 channel and run the 3.5" speakers on the front channel, and the 6x9's on the rear. The only down fall is, fading will not that usable. With a 5ch amp, you can add a sub. Ideally, going with an 8ch or 2-4ch amps will be ideal. Then, a mono block for the subs. </p><p></p><p>Check out these amps. They are good quality at a really good price.</p><p></p><p>[URL unfurl="true"]https://www.amazon.com/dp/B09V2SXWJX/?tag=caraudiocom-20[/URL]</p><p></p><p>[URL unfurl="true"]https://www.amazon.com/dp/B09V2R9XL6/?tag=caraudiocom-20[/URL]</p></blockquote><p></p>
[QUOTE="Old_Slapper, post: 8880438, member: 690458"] 1. You can run speakers from the aftermarket amp to the factory amp. From there, you can tap into the factory speaker wires that go to the speakers. 2. Always go off the RCA outputs of an aftermarket radio. The LOC's have a tendency to filter out some tones. 3. Your 3.5" speakers will handle less power and a higher frequency than the 6x9s. You can use a 4 channel and run the 3.5" speakers on the front channel, and the 6x9's on the rear. The only down fall is, fading will not that usable. With a 5ch amp, you can add a sub. Ideally, going with an 8ch or 2-4ch amps will be ideal. Then, a mono block for the subs. Check out these amps. They are good quality at a really good price. [URL unfurl="true"]https://www.amazon.com/dp/B09V2SXWJX/?tag=caraudiocom-20[/URL] [URL unfurl="true"]https://www.amazon.com/dp/B09V2R9XL6/?tag=caraudiocom-20[/URL] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
General Car Audio
Adding amp using existing oem speaker wiring
Top
Menu
What's new
Forum list