Item(s) for Sale:
I have an Addictive Audio 500.1 that is #37 out of 50 that were produced for the first run.
Rated at 500 watts @ 4 ohms //content.invisioncic.com/y282845/emoticons/rolleyes.gif.c1fef805e9d1464d377451cd5bc18bfb.gif
Does over 5k @ 1 ohm and should do around 6k at .5 ohm. I never tested this one at .5 but most people say that it does .5 fine if you have the electrical to back it.
Item(s) Description/Condition:
Cosmetically I would give it about a 6/10 it looks good for the most part but the mounting feet are rough and a couple dings on the edges and the back cover is purple.
Mechanically I have to give it a 9/10 only because the "remote level" input for the factory bass knob got a little messed up during shipping when I received it, but I have tested it in a friends vehicle and it worked great and it was very strong. Also if you use a PAC-LC1 for the knob there is no need for the "remote level" input.
This was also repaired by Cory Brandes who has done various repairs and mods to these amps so it was definitely done right. Here is what he sent me about this one. "I bought it from a kid who shorted the speaker wires. One of the output caps and trace was blown. I replaced the output FETs since I had the output board pulled."
Price:
I am asking $650 + shipping for this amp. As far as trades go I am looking for a nice double din, a 4 channel amp that does 100+ x4 @ 4ohm, Wire and deadener.
Shipping and Miscellaneous Item Information:
Shipped and insured via UPS
Item Pictures:
(List pictures in this section, 1st picture should be your username/date if you have less than 10 positive feedbacks with the i-Trader system or less than 10 references that you have sold to in the past. (These must be listed in your signature, or a link provided to a feedback thread listing these references)).
I have an Addictive Audio 500.1 that is #37 out of 50 that were produced for the first run.
Rated at 500 watts @ 4 ohms //content.invisioncic.com/y282845/emoticons/rolleyes.gif.c1fef805e9d1464d377451cd5bc18bfb.gif
Does over 5k @ 1 ohm and should do around 6k at .5 ohm. I never tested this one at .5 but most people say that it does .5 fine if you have the electrical to back it.
Item(s) Description/Condition:
Cosmetically I would give it about a 6/10 it looks good for the most part but the mounting feet are rough and a couple dings on the edges and the back cover is purple.
Mechanically I have to give it a 9/10 only because the "remote level" input for the factory bass knob got a little messed up during shipping when I received it, but I have tested it in a friends vehicle and it worked great and it was very strong. Also if you use a PAC-LC1 for the knob there is no need for the "remote level" input.
This was also repaired by Cory Brandes who has done various repairs and mods to these amps so it was definitely done right. Here is what he sent me about this one. "I bought it from a kid who shorted the speaker wires. One of the output caps and trace was blown. I replaced the output FETs since I had the output board pulled."
Price:
I am asking $650 + shipping for this amp. As far as trades go I am looking for a nice double din, a 4 channel amp that does 100+ x4 @ 4ohm, Wire and deadener.
Shipping and Miscellaneous Item Information:
Shipped and insured via UPS
Item Pictures:
(List pictures in this section, 1st picture should be your username/date if you have less than 10 positive feedbacks with the i-Trader system or less than 10 references that you have sold to in the past. (These must be listed in your signature, or a link provided to a feedback thread listing these references)).