Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Help
Enclosure Design & Construction
4th Order Wall Design Help Needed
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="nutnbutcustm" data-source="post: 7978568" data-attributes="member: 576497"><p>I have been building systems for about 16 years I just never have built or messed with a 4th order.but i have decided no better time than now! so here is my info....</p><p></p><p>Purpose: street beat I want to do demos and do street beat in usaci so my goal is to do 160+ on music @47hz for 30 seconds at a time. I say 47hz because my truck peaks at 45 and 47hz is the track i have to use for street beat.</p><p></p><p>equipment: I have 4-12" B2 XC's being powered by 2-B2 M1's I could swap out to 15's but would like to stay with the 12's if my goal is attainable with them.</p><p></p><p>space: I have a 2005 Nissan Xterra that i can do anything with, my demensions are roughly 40"wide 36"tall 40" deep</p><p></p><p>i can go bigger but i would like to keep it this size or smaller to be able to remove the box to try different designs. it has a false floor "base" already installed. also would like to use a large aero port for the front chamber tuning rather than a slot port.</p><p></p><p>If you need anymore info just let me know, and if i need to pay you something just let me know.</p><p></p><p>B2 XC 12" specs</p><p></p><p>Power Handling: 6 kw ~ 15 kw*</p><p></p><p>Sensitivity: 86.1 dB</p><p></p><p>Nominal Impedance: 1 Ω</p><p></p><p>(Re):0.9 Ω</p><p></p><p>Resonanse Frequency (Fs): 38.3 Hz</p><p></p><p>Vas: 16.51 L</p><p></p><p>Qts: 0.331</p><p></p><p>Qms: 4.848</p><p></p><p>Qes: 0.356</p><p></p><p>Voice Coil diameter: 4"</p><p></p><p>I have tried to message @80inches but his pm box is full so anybody else have any advice? this is a huge build with some pricey equipment so please only help from guys that have built and have a lot of experience with 4ths please! and thanks in advance for any help!</p></blockquote><p></p>
[QUOTE="nutnbutcustm, post: 7978568, member: 576497"] I have been building systems for about 16 years I just never have built or messed with a 4th order.but i have decided no better time than now! so here is my info.... Purpose: street beat I want to do demos and do street beat in usaci so my goal is to do 160+ on music @47hz for 30 seconds at a time. I say 47hz because my truck peaks at 45 and 47hz is the track i have to use for street beat. equipment: I have 4-12" B2 XC's being powered by 2-B2 M1's I could swap out to 15's but would like to stay with the 12's if my goal is attainable with them. space: I have a 2005 Nissan Xterra that i can do anything with, my demensions are roughly 40"wide 36"tall 40" deep i can go bigger but i would like to keep it this size or smaller to be able to remove the box to try different designs. it has a false floor "base" already installed. also would like to use a large aero port for the front chamber tuning rather than a slot port. If you need anymore info just let me know, and if i need to pay you something just let me know. B2 XC 12" specs Power Handling: 6 kw ~ 15 kw* Sensitivity: 86.1 dB Nominal Impedance: 1 Ω (Re):0.9 Ω Resonanse Frequency (Fs): 38.3 Hz Vas: 16.51 L Qts: 0.331 Qms: 4.848 Qes: 0.356 Voice Coil diameter: 4" I have tried to message @80inches but his pm box is full so anybody else have any advice? this is a huge build with some pricey equipment so please only help from guys that have built and have a lot of experience with 4ths please! and thanks in advance for any help! [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Enclosure Design & Construction
4th Order Wall Design Help Needed
Top
Menu
What's new
Forum list