Recent content by robinredd

im a girl and i have been going threw amps and i just can not get the sound im looking for but i have a few  speakers, subs, and amps and im not a professional by far but im always finding myself disconnecting the power wire so i can change speakers  around with the amps trying to get more sound...

I found a Lanzar Max MXA 234 MOSFET at a garage sale. Max Series 2-Channel Car Amplifier RMS Power Rating (14.4V): 4 ohms: 100 watts x 2 chan. 2 ohms: 150 watts x 2 chan. Bridged, 4 ohms: 2000 watts x 1 chan. RMS Power Rating (THD): 4 ohms: 150 watts x 2...

got thank you iI have a question i hooked up the clarion to the 4 channel daul amplifier. Channels 1 and 2 will be bridged to the subwoofer coil #1.  Channels 3 and 4 will be bridged to the subwoofer coil #2. when i reached back to get something i noticed the daul amp was pretty hot is that...

i got the sub wiring done i got that one one coil to one the other coil to the other channel bridged got it thank you it is the 4 6x9 is where im have the difficultys 

im not sure exactly what your talking about "Yes, all positives will combine but they can combine at the amp terminals.  So route wiring from each 6x9 to the respective amp.  On the Encore, you'll land two wires in each terminal. " all positives will combine but they can combine at the amp...

i forgot to upload the picture of the diagramhttps://www.sonicelectronix.com/product/img/subwoofer_wiring/4_subs_SVC_4_ohm_2ch.jpg

i have looked on the internet and i can only find this diagram for 4 speakers to a 2 channel amp but it is for subs will this aply for the 4 6x9? if so it going to be a little tricky with the 2 being mounted in the upper rear and the 2 external loose in their boxes in the back seat but if this...

thank you so much ok this is what im understanding you think it would be better for me to use the encore for the 4 rear speakers (6x9). and use the dual 4 channel amp for the one clarion  dual coil. the wiring diagram above i would choose the 4ohm to 2ohm one for the sub . my question is out...

My car is a Pontiac grand prix  .i have ruled out the 10" fosgate speaker and i had a third kenwood 2 channel amp i was going to power the front door speakers but someone told me that using the output rca from the 2 channel encore amp that i was going to use for the sub to get signal to the...

so basicly your saying to run the 4 six by nines one per channel would be the best for the amp or speakers or sound? because when i did have them hooked that way the sound wasn't that loud than like when they are bridged but is having them bridged bad for the speakers?

did you see my other question i posted and yes diagrams really help alot

i got a package i got to put together that i sold on ebay and mail it it may be a minute before i answer back thank you for talking to me i have learned a lot from watching you tube videos and reading about ohms and running series and parallel but theirs still a lot i dont know and ill...

im so sorry  if you go to a different question titled a girl needs help i asked yesterday it has all the info i forgot the specs were not in this question. another  question they want you to use huge wire for the amps but the part you connect it to  you can hardly if at all get the whole wire to...

I used 3 awg power wire and 8 awg ground and 16 awg remote and 16 awg speaker I got the amp without a remote screw and i use a wedge to hold the wire in till i get a new screw Im going to fix the screw issue . I was just curious if from the specs on the previous message bridged to the amp was...

thankyouforansweringyoucouldnthavebeenmorerightonwithhurtingmyfeeling