Recent content by jcash1995

I'm still in the planning phase for my 84 Mustang convertible I'm planning on using 2 10" subs (not sure on brand yet) I'm trying to figure out how to get around the convertible top when down. My car has a glass rear window that with the top down leaves very little space at the bottom of the...

I have an FBX-10 in a 1.5 ft poerted enclosure tuned to 35 hz with only 100 watts to each coil and just had it rta'd at a local shop......134 db. My official review: Excellent SPL sub, gets very loud wuth little power. sound quality, not too bad. maybe it's my setup, or the amp, but bass is...

I'm using an LT-960-4 to power a single Power Acoustk FBX-10 and Clarion 5 1/4 components and I'm VERY happy with it. The crossover settings are a little vague, but overall very worth the money (got a deal on SD, sub and amp for $220)

I just bought (today) my first Brand new car. 2003 Nissan Sentra seR. I love this car........except the factory sub. This car has the 7 speaker system, not the Rockford Fosgate System(I think). Anyway, I will be replacing the 8" sub because it souds like it's hitting the back deck. Can anyone...

If I remember correctly, all 87-93 mustangs also had 5 1/4's in the doors. When I had my 87, I built an mdf baffle to go over the stock opening and mounted Clarion 5 1/4's (even though this was 5 years ago, they are in my beretta now, and still sound great!!) http://www.geocities.com/jcash1995...

I'll just try it. Worst case, I'll need a better alt. THNX!

"TEMPORARILY OUT OF STOCK" :thumbsdow

Go here: http://www.sonicelectronix.com/viewitem.php?id=1572 Scroll down to the link for the product manual. put the speaker parameters into winisd. Now plot a ported enclosure using 2 woofers. 2.2 cubic feet tuned to 30 hz. NOW THAT IS A FLAT RESPONSE!!!

I know it's a little late, But I gotta reply. I'm assuming your mustang has a trunk, not a hatch. Therefore it is always a good idea to use a baffle around your rear-fill speakers to keep the pressure from the sub from pushing your cones out. Always a good idea to use baffles especially in a...

Hey misterio! If it gets me away from WinIsd, I want a copy too!! PLEASE.

my parts for my new system will be here soon. See Sig. I'm going to build a sliding amp rack to put my amps underneath my subbox. what is the best way to run the wiring to keep it neat and out of the way of the sliders. How does everyone else do it?? Here is my idea: All my wires will run out...

I'm getting ready to install a JBL BP600.1 and a P80.4 in my 93 beretta. Stock alternator, no power windows/locks, etc. I have already done the Big 3. If I figured this right, I need an alt that does 110 amps. Is this right? Or am I just overthinking this?

Too late to change my mind now. The TI 15d is in the mail :veryhappy

XS-L1099X This Ad is for only ONE Woofer 10" Sub Woofer 1500 Watts Peak power 150 Oz Magnet Double Magnet Bumper Back Plate 5-Sided Polyethylene Cone=Lower Distortion And louder, Deeper Bass Rubber Surround With "Smoke Stabilizer" 4-Layer Edge Wound 4 Ohm Voice Coil Dual Voice Coil...

If you HAVE to do one or the other, grab the sealed. But, I just ran both combos on WinIsd, and the PG 10 would really sound great in the ported.......tuned to 30hz, not 40. VERY linear response all the way down to 35 hz with a -3 drop off at 25 hz. The sealed has a -3 at 53 hz. My final...