Sub not hitting like it should

  • 3
    Participant count
  • Participant list

So good 4U

CarAudio.com Newbie
Hi I am looking for some insight into why I'm not getting the performance I'm looking for, I have seen videos on YouTube with smaller amps shaking cars to s**t. The Sub is a Alpine Type R-10d4 wired to 2 ohm load it is in a Scar armor box with a 1" wide kerf port (1.4 ft³ @38hz) the amp is a Infinity 611a (657 watts at 2 ohm). The amp did well pushing two Rockford Fosgate P1's also wired to a 2 ohm load, before they tapped out and locked up. All other system info big 3 upgrade, 4 gauge wire, dual head unit "I know" and pioneer g series in doors.
 
You are not giving that subwoofer enough power. The RMS on it is 750 so you are under-powering it by a decent amount. Putting it on a bigger amplifier will do wonders for that subwoofer. Those are known to get down. Your 38hz might be a bit much but a Box Designer there would know better then me. But what you play for music as well helps. I also would think about doing a 2nd subwoofer if you can and then getting a bigger mono-block amplifier that can run at 1ohm. Type Rs need power and right now you just don't have enough of it. Then you would also have to upgrade to 1/0 for the amplifier as well but that is no big deal.
 
Thanks for the advice I was just looking at the crutchfield website and they said it is a power hungry speaker, I bought it with the idea of future proofing as like you said it can be wired a lot of ways. I will be looking for an amp that does 1500 watts rms at 1ohm so that right now I can run the one speaker at 2 ohm 750 watts and when I get a second speaker I can run 1500 watts at 1 ohm. Any suggestions on an amp that fits the bill? I like the Scar box but I don't know how there amps are they seem to cheap to be any good.
 
Type R subs can get down fairly decent with some power and a good tuned enclosure.The older Type Rs really did some work at quite a few shows I was able to demo. Run a pair in approx 4.0 Cu. Ft @ 32-35 HTZ and put a Taramps 3k on them, and they should get down very nicely for a pair of 10s. Get that supply for the Demand situated as well, and I think you will be fairly happy till you decide to ugrade again later.
 
Activity
No one is currently typing a reply...
Old Thread: Please note, there have been no replies in this thread for over 3 years!
Content in this thread may no longer be relevant.
Perhaps it would be better to start a new thread instead.

Similar threads

That does sound similar to what mine does, I'll take a video and post it this weekend so you guys can weigh in.
23
5K
Getting a good voltage reading does not mean good power transfer. You could read 13.8v out of a 24 AWG wire. Recheck your amplifier's ground and...
2
202
That would be a function of the harness, not the HU, I think. Have you looked into a Maestro or iData interface? i would check with crutchfield...
12
541
thanks DB, that definitely helps swallowing a $300 price tag 😂 these would essentially be running midbass for me too
12
572

About this thread

So good 4U

CarAudio.com Newbie
Thread starter
So good 4U
Joined
Location
minnesota
Start date
Participants
Who Replied
Replies
3
Views
1,198
Last reply date
Last reply from
audiobaun
20240604_170857.jpg

metalheadjoe

    Jun 5, 2024
  • 0
  • 0
Screenshot_20240605_200209_Adobe Acrobat.jpg

Dylan27

    Jun 5, 2024
  • 0
  • 0

New threads

Top