installing a volt meter.
- Thread starter BoomBoxStereo
- Start date
- Replies 15
- Views 3K
-
11Participant count
-
Participant list
BoomBoxStereo
rebelfromva 10+ year member
CarAudio.com Veteran
I put mine in the side holder where I press the button to pop the trunk
bgowdy 5,000+ posts
Heroes are remembered, but legends never die
i ran mine threw my truck and used double sided tape and stuck it on my middle console of my blazer
Below20hzonly 10+ year member
CarAudio.com Elite
do you have any room right below the HU?
CAT MAN 5,000+ posts
Banned
in the ashtray since i dont smoke
goingdef 10+ year member
CarAudio.com Veteran
I didn't like the fact that I had two clocks about 3" from each other so I removed the lcd screen and kept the oem tinted look by double side taping the screen in from behind then ran to the HU for the on/off function. I like it it looks stock even when it's on people are always asking what's wrong with the clock?
OP
BoomBoxStereo 10+ year member
@woofergram
- Thread Starter
- #7
not much... it's an 07 Jeep Liberty.
this isn't my car, but this is how the interior is set up...
goingdef 10+ year member
CarAudio.com Veteran
well with your interior pick a panel that is easily/cheaply replaceable and with a little bondo work followed with some matching paint and it should look good, check ebay for the panel and modify that one not your stock that way at a moments notice you can go back to stock and if the modded panel looks good you can probably sell it.
RangerDangerV2 5,000+ posts
CarAudio.com Veteran
I thought about cutting out the stock batt gauge and replacing it with my volt meter...
goingdef 10+ year member
CarAudio.com Veteran
be careful screwing around with your gauge cluster there kind of fragile.
RangerDangerV2 5,000+ posts
CarAudio.com Veteran
ill just tape the bish up then.
OP
BoomBoxStereo 10+ year member
@woofergram
- Thread Starter
- #12
lolol
I oput mine behind where the ashtray used to go in my Honda Accord
keep_hope_alive Premium Member
Acoustics Engineer
just buy a plug-in one.
Digital Cigarette Lighter Voltage Gauge | NLD-06 (NLD06) | Distributed By MCM
Digital Cigarette Lighter Voltage Gauge | NLD-06 (NLD06) | Distributed By MCM
Activity
No one is currently typing a reply...
Similar threads
I would prob go and take it to a shop to someone that knows how to install, pay the $50-75-100 bucks so its done correctly.If you continue to do...
- Started by tripdls
- Wiring, Electrical & Installation
There are a couple that SMD has tested, around $20.00 that should take the wattage from most any HU. If you are tapping into the speaker wires...
- Started by AudioArchitech
- Wiring, Electrical & Installation
The Kicker LOC at around $20.00 does the same thing,
- Started by Imperiumwolf
- Wiring, Electrical & Installation
for my amp ground I have it to the paneling in my trunk, secured with a bolt and a nut. I sanded as much as I could, and I used a grind wheel on...
- Started by EmpiricalApe
- Wiring, Electrical & Installation 3 4 5
About this thread
- Start date
- Participants
- Who Replied
- Replies
- 15
- Views
- 2,639
- Last reply date
- Last reply from
- VisceralSound
Latest topics
-
Jeep center console sub install issues.
- Started by vlusardi
- Replies: 1
-
-
-
-
Help With Kenwood DDX9907XR / DMX907S - Kenwood Technical Support Can't Help
- Started by fadetoblack73
- Replies: 5