Battery Question.

When you connect pos to pos and neg to neg on the battery you will get 24 volts, not 12 volts. this is called a parallel connection and this is not good for and 12 volt system. You WILL be blowing fuses like how the avg American spends money...lol.

You want to connect it in series (pos to neg and pos to neg). By doing so, you will recieve 12 volts. Your storage capacity of your battery will increase.

hope this helps. If not check this out: http://www.caraudio.com/forum/showthread.php?t=198742

When you connect pos to pos and neg to neg on the battery you will get 24 volts, not 12 volts. this is called a parallel connection and this is not good for and 12 volt system. You WILL be blowing fuses like how the avg American spends money...lol.
You want to connect it in series (pos to neg and pos to neg). By doing so, you will recieve 12 volts. Your storage capacity of your battery will increase.

hope this helps. If not check this out: http://www.caraudio.com/forum/showthread.php?t=198742

Click to expand...

That will give him 24 volts, Do not listen to what he said, u want pos to pos, and neg to neg to ground. (U should know not to listen to him just by looking at how he uses a cap. lol)

When you connect pos to pos and neg to neg on the battery you will get 24 volts, not 12 volts. this is called a parallel connection and this is not good for and 12 volt system. You WILL be blowing fuses like how the avg American spends money...lol.
You want to connect it in series (pos to neg and pos to neg). By doing so, you will recieve 12 volts. Your storage capacity of your battery will increase.

hope this helps. If not check this out: http://www.caraudio.com/forum/showthread.php?t=198742

Click to expand...

//content.invisioncic.com/y282845/emoticons/laugh.gif.48439b2acf2cfca21620f01e7f77d1e4.gif your going to blow up his car! that's mean. False information FTL!

dB

When you connect pos to pos and neg to neg on the battery you will get 24 volts, not 12 volts. this is called a parallel connection and this is not good for and 12 volt system. You WILL be blowing fuses like how the avg American spends money...lol.
You want to connect it in series (pos to neg and pos to neg). By doing so, you will recieve 12 volts. Your storage capacity of your battery will increase.

hope this helps. If not check this out: http://www.caraudio.com/forum/showthread.php?t=198742

Click to expand...

Oh Boy...

Hello,

I would put a 200/Amp Solenoid in if you want to do Key-Off listening(Your Choice of course/ ).That way you can do that without draining your starting battery.

Just a thought.Good luck with your system.

*Kind Regards*,

i put pos to pos and neg to neg and my 2nd battery boiled so much that it was like a guyser. Could the problem of been the fact that when i put in the 2nd battery it was almost completly dead?

possible, or it could have had a beat cell, i had similar type issue's

pos to pos and neg to neg is fine

The reason why your battery boiled over is because you hooked it up in parallel. Pos to pos and neg to neg to both batteries sees 24 volts not 12 volts. Trust me, I did a lot of research on it. //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

When you connect pos to pos and neg to neg on the battery you will get 24 volts, not 12 volts. this is called a parallel connection and this is not good for and 12 volt system. You WILL be blowing fuses like how the avg American spends money...lol.
You want to connect it in series (pos to neg and pos to neg). By doing so, you will recieve 12 volts. Your storage capacity of your battery will increase.

hope this helps. If not check this out: http://www.caraudio.com/forum/showthread.php?t=198742

Click to expand...

Wrong again da12b, perallel gives you double the current

Series gives you double the voltage, read what other people post

kthxby

and keep researching //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

http://www.kinetikaudio.com/manuals/khccells.pdf da needs to read this

Sorry, my quote was wrong. The correct ans is; series connection = 12 volts and parallel connection = double the voltage.

Sorry for the wrong info.

check out this site: http://www.otherpower.com/otherpower_battery_wiring.html

Thanks for correcting me.

When you connect pos to pos and neg to neg on the battery you will get 24 volts, not 12 volts. this is called a parallel connection and this is not good for and 12 volt system. You WILL be blowing fuses like how the avg American spends money...lol.
You want to connect it in series (pos to neg and pos to neg). By doing so, you will recieve 12 volts. Your storage capacity of your battery will increase.

hope this helps. If not check this out: http://www.caraudio.com/forum/showthread.php?t=198742

Click to expand...

WTF???

here ya go.

edit:nevermind wrong picture

http://www.kinetikaudio.com/manuals/khccells.pdf da needs to read this

Click to expand...

Would it be better to ground the 2nd battery as well or is that not needed?