Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Wiring Help!? Question on Wire Brand & Question on How to Wire 4 Channel
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="bgolightly82" data-source="post: 7183181" data-attributes="member: 625891"><p>Ok, so question 1. I currently have a Memphis 1/0 wire kit (super flexible!), its really nice wire (over $200 retail). But I am going to need much more 1/0 and 4 and 8. I was thinking about going with KnuKoncepts (not the Copper Clad Aluminum ****), which I hear is a pretty good wire and way cheaper than the memphis! So my question is, is the KnuKoncepts good enough that I should just buy it in bulk and use just that, then sell the Memphis? Or should I really just bite the $ and buy more Memphis? I'll be running about 3.5k for all. Think the KnuKoncepts is decent enough at that level?</p><p></p><p>Question 2. I have a set of ID 6.5 Comps, and a set of ID 6x9's (all are 4 ohm / 100 rms) with the Soundstream DTR4.500 (4 channel - 80x4 @ 4 / 125x4 @ 2). So I obviously want to run it at 2 ohms, but how do I wire it to speakers?</p><p></p><p>I looked at the wiring diagram for it in the manual, but they are just wired to each channel, which wouldn't that just be 4 ohms?</p></blockquote><p></p>
[QUOTE="bgolightly82, post: 7183181, member: 625891"] Ok, so question 1. I currently have a Memphis 1/0 wire kit (super flexible!), its really nice wire (over $200 retail). But I am going to need much more 1/0 and 4 and 8. I was thinking about going with KnuKoncepts (not the Copper Clad Aluminum ****), which I hear is a pretty good wire and way cheaper than the memphis! So my question is, is the KnuKoncepts good enough that I should just buy it in bulk and use just that, then sell the Memphis? Or should I really just bite the $ and buy more Memphis? I'll be running about 3.5k for all. Think the KnuKoncepts is decent enough at that level? Question 2. I have a set of ID 6.5 Comps, and a set of ID 6x9's (all are 4 ohm / 100 rms) with the Soundstream DTR4.500 (4 channel - 80x4 @ 4 / 125x4 @ 2). So I obviously want to run it at 2 ohms, but how do I wire it to speakers? I looked at the wiring diagram for it in the manual, but they are just wired to each channel, which wouldn't that just be 4 ohms? [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Wiring Help!? Question on Wire Brand & Question on How to Wire 4 Channel
Top
Menu
Home
Refresh