New amp gets hot when powered up?

[One_crazy_dude]

Hey all. Got an Orion xtr 2500.1 today. I removed a cab 1600.1 in working order just to add more power to my hdc 3.115 sub that is wired down to 1 ohm.

So I swap out power ground and remote wire and start the car. I do this to make sure it powers on. And power on it did. But I notices it was getting warm on the top half of the amp and in a minute or so it was hot but the bottom half is still cool. Mind you no rca's or speaker wires are hooked up yet so it's not loaded at all.

So I wait a good 10 minutes and it's hot but doesn't go into protect or anything so in plug in the 8 gauge speaker wires and rca's and music plays and plays loud but it gets hot. I played music for about a 1/2 hour and it has not gone into protect or anything.

I've had quite a few amps in my time and never had them get hot while just powered on and no signal going to it. Should I send it back? What would you do?

Click to read more...

 

[Louisiana_CRX 5,000+ posts]

Hey all. Got an Orion xtr 2500.1 today. I removed a cab 1600.1 in working order just to add more power to my hdc 3.115 sub that is wired down to 1 ohm.
So I swap out power ground and remote wire and start the car. I do this to make sure it powers on. And power on it did. But I notices it was getting warm on the top half of the amp and in a minute or so it was hot but the bottom half is still cool. Mind you no rca's or speaker wires are hooked up yet so it's not loaded at all.

So I wait a good 10 minutes and it's hot but doesn't go into protect or anything so in plug in the 8 gauge speaker wires and rca's and music plays and plays loud but it gets hot. I played music for about a 1/2 hour and it has not gone into protect or anything.

I've had quite a few amps in my time and never had them get hot while just powered on and no signal going to it. Should I send it back? What would you do?

You use to could cook a steak on the old school Orion Reds back in the day but like a timex they kept on ticking

 

[BOOMINGRANDPA 5,000+ posts]

Hey all. Got an Orion xtr 2500.1 today. I removed a cab 1600.1 in working order just to add more power to my hdc 3.115 sub that is wired down to 1 ohm.
So I swap out power ground and remote wire and start the car. I do this to make sure it powers on. And power on it did. But I notices it was getting warm on the top half of the amp and in a minute or so it was hot but the bottom half is still cool. Mind you no rca's or speaker wires are hooked up yet so it's not loaded at all.

So I wait a good 10 minutes and it's hot but doesn't go into protect or anything so in plug in the 8 gauge speaker wires and rca's and music plays and plays loud but it gets hot. I played music for about a 1/2 hour and it has not gone into protect or anything.

I've had quite a few amps in my time and never had them get hot while just powered on and no signal going to it. Should I send it back? What would you do?

yeah but what size wire u have? hope 0ga.. it's tight.. but yeah some stuff just heats up fast man..

 

[Louisiana_CRX 5,000+ posts]

yeah but what size wire u have? hope 0ga.. it's tight.. but yeah some stuff just heats up fast man..

Pure copper zero as well because zero aluminum wire isn't any better than pure 8g copper ...

 

[BMayes36]

You use to could cook a steak on the old school Orion Reds back in the day but like a timex they kept on ticking

Just don't keep it on there to long, I like mine rare.

 

[Louisiana_CRX 5,000+ posts]

Just don't keep it on there to long, I like mine rare.

I always liked mine medium rare

 

[Boomin_tahoe 5,000+ posts]

yeah but what size wire u have? hope 0ga.. it's tight.. but yeah some stuff just heats up fast man..

This and what ohm load are you giving that amp? If it's 1/2 ohm it's gonna heat up fast.

 

[One_crazy_dude]

Power wire is 1/0 guage. I also have 3 100 ah agm batteries, 2 in back 1 in front. I understand amps get hot but this one gets hot while rca's and speaker wires are disconnected.

 

[Louisiana_CRX 5,000+ posts]

Power wire is 1/0 guage. I also have 3 100 ah agm batteries, 2 in back 1 in front. I understand amps get hot but this one gets hot while rca's and speaker wires are disconnected.

That sure doesn't sound right at all ..maybe a bad solder joint on the circuit board

 

[youdoofus]

Power wire is 1/0 guage. I also have 3 100 ah agm batteries, 2 in back 1 in front. I understand amps get hot but this one gets hot while rca's and speaker wires are disconnected.

if im not mistaken, the MOSFETs are usually on the side of the PCB boards and would heat up exactly where youre talking about. I dont like the sound of this and wouldnt be too hesitant to return it. Its probably a repaired amp with either a poor repair job or wrong transistors installed during said repair. If its gettin pretty hot with no audio source nor speakers connected to it, thats a red flag to me. My SQ2200.1 stays very cool even when im beating on it fwiw

 

[One_crazy_dude]

if im not mistaken, the MOSFETs are usually on the side of the PCB boards and would heat up exactly where youre talking about. I dont like the sound of this and wouldnt be too hesitant to return it. Its probably a repaired amp with either a poor repair job or wrong transistors installed during said repair. If its gettin pretty hot with no audio source nor speakers connected to it, thats a red flag to me. My SQ2200.1 stays very cool even when im beating on it fwiw

I agree. It is a new amp as far as I know of so I called amazon and it's going back. I just don't feel safe with this thing heating up for no reason. Thanks.

 

[Boomin_tahoe 5,000+ posts]

I agree. It is a new amp as far as I know of so I called amazon and it's going back. I just don't feel safe with this thing heating up for no reason. Thanks.

Was the amp new, refurb, or b stock, open box item when you bought it?

 

[One_crazy_dude]

Was the amp new, refurb, or b stock, open box item when you bought it?

The amp is new.

 

[Boominburban]

Return ...

 

[Jeremyb002]

That sure doesn't sound right at all ..maybe a bad solder joint on the circuit board

Capisitors inside sam young 250v 10uf