Mtx 8100d Vs Mtx 1501d

i believe it's teh same amount of power. there might be a diff @ 4ohms, but i am very sure tha tu wont be runnin that beast @ 4ohms anyways

 
MTX 1501D:

RMS Power: 750W x 1 @ 4 ohms

Bridged RMS Power: 1500W x 1 @ 2 ohms

MTX 81000D:

Power 12.5 VDC Input

2 Ohm Load 1000 w x 1

4 Ohm Load 500 w x 1

Power 14.4 VDC

2 Ohm Load 1500 w x 1

4 Ohm Load 850 w x1

Although i think the 81000d is a little more underrated than the 1501d

 
I just got a 1501d and it is rated at 1163 watts at 12 volts. It definitely is a beast. Hey BDiddy -- do you have 4 gauge or 0/1 gauge power. Also, how are you powering that amp? New alt? Caps? Batts? BatCaps? My alt is only 90 amp, and there are no upgrades available from ANYONE -- thinking on a batcap and 35 farad capacitor(Unless I can sell my whole setup). Any input is appreciated

 
I just got a 1501d and it is rated at 1163 watts at 12 volts. It definitely is a beast. Hey BDiddy -- do you have 4 gauge or 0/1 gauge power. Also' date=' how are you powering that amp? New alt? Caps? Batts? BatCaps? My alt is only 90 amp, and there are no upgrades available from ANYONE -- thinking on a batcap and 35 farad capacitor(Unless I can sell my whole setup). Any input is appreciated[/quote']

I have 1/0 gauge running to mine, because it's recommended. But CC runs 4 gauge to theirs. I don't have a upgraded amp or a cap. My alt can't be more than 90 also. It would probably be louder if I had more juice to give out but you could probably get your rewound. Also http://www.weldingsupply.com has 1/0 for .99 a ft. People say it's really flexible too.

Hope this helps...
 
Activity
No one is currently typing a reply...
Old Thread: Please note, there have been no replies in this thread for over 3 years!
Content in this thread may no longer be relevant.
Perhaps it would be better to start a new thread instead.

Similar threads

Thanks buddy! Given me a lot to think about in terms of what to do; I've been watching YouTube videos on this stuff all day as well so I really...
4
971
You can wire those subs up @8 ohms if they are both SVC4 ohm subs,and that amp will run fine after being tuned properly...
4
1K
The 240 should be 2x40/ 2ch. rated at 11.9v. Should generate close to 50+ @14v rms. Only Rated @4 ohms bridged Mono.. Should be around 125 rms...
5
3K
In 1990: The MTX MTA 225 had a MSRP of 549.95 25x2 0.02% THD S/N 102 12x 8 1/2x 2 3/8 The MTX MTA 250 had a MSRP of 649.95 50x2 0.02% THD S/N...
5
2K

About this thread

lcpunk69

10+ year member
SQ Baby!
Thread starter
lcpunk69
Joined
Location
Gainesville, FL
Start date
Participants
Who Replied
Replies
9
Views
5,776
Last reply date
Last reply from
goodrich
20231205_074421.jpg

spokey9

    Jul 17, 2024
  • 0
  • 0
Screenshot_20240715-132222.png

1aespinoza

    Jul 15, 2024
  • 0
  • 0

New threads

Top