Jump to content

spencer321

Members
  • Content count

    1,768
  • Joined

  • Last visited

  • Feedback

    0%

Community Reputation

0 Neutral

About spencer321

  • Rank
    CarAudio.com Elite
  • Birthday 01/13/1987

MORE INFO

  • Location
    palm bay
  • Interests
    this?
  1. spencer321

    fiberglass question, 3oz vs 1.5oz vs .75oz

    I really appreciate it but I have this thing about doing it myself or not at all lol not talking about evan by any chance are you?
  2. spencer321

    fiberglass question, 3oz vs 1.5oz vs .75oz

    Technically it should take twice as much resin but its a long panel so 4 layers of 1.5 or 2 layers of 3 should be the same, I appreciate it guys, going to give the 3oz stuff a shot, if I find it unbearable to work with at least I should figure it out in the mold stage and not have to ruin a whole piece
  3. spencer321

    fiberglass question, 3oz vs 1.5oz vs .75oz

    Putting some silverflute 8s in my crown vic doors, replacing rsd6.5 mids
  4. spencer321

    fiberglass question, 3oz vs 1.5oz vs .75oz

    Putting some silverflute 8s in my crown vic doors, replacing rsd6.5 mids
  5. spencer321

    fiberglass question, 3oz vs 1.5oz vs .75oz

    posting "builds" I get too involved and forget to pick up a camera but ill try to make a decent build thread. Im not so much worried about weight as flexibility. If 3oz is that heavy duty I can do 2 layers and be done im just concerned with how workable it is, if it doesn't conform or bend easily ill get to save a layer but create twice the work fighting with the stuff. I can get 1.5 and even .75 but instead of a 5 minute drive its an hour drive.
  6. Got a new car, have to remake door pods, ive done doorpods before but the door was flat so I had a MDF back plate. New doors are not flat but have a nice cavity to get a backing mold from. Local marine store only carries 3oz chopped mat, most tutorials ive seen say to use 1.5oz, Im curious if the 3oz chop is going to be too stiff to work with. anyone with experience in any weight csm please chime in amd describe your experience
  7. spencer321

    Re-coned SA10's, 12's, and 15's

    nevermind, should have read the thread
  8. yeah i opened it up, didn't see anything burnt, i looked over every part of it very carefully but i also don't know what im doing, i just looked for burnt spots or broken solder connections and didn't see any
  9. no its the amp... i started workin on it, been disconnected for a few days, now it goes straight into protect, so i disconnected everything and hooked it straight to the battery and jumped the remote to the positive, straight into protect... so i opened up the back of it... what am i looking for? or should i just pitch it and say to hell with it?
  10. checked the power and ground... its steady, plus my highs amp is off the same distro block one foot away and that amp is perfectly fine. Pulled the sub, Dual 4ohm coils read 3.9 on each coil, checked and double checked all my wiring, it all seems fine, the only thing i haven't gone through is the signal wire itself... is it possible for a short or a bad signal wire to cause this problem? symptom: turn the car on plays fine for a minute, then a couple really loud pops and protect
  11. spencer321

    trading my hdc312 for a precision PC18DS, bad idea?

    so anyone familiar with the subwoofer in question?
  12. spencer321

    trading my hdc312 for a precision PC18DS, bad idea?

    ok, well once again, the question was from A... to B... now 90% of ppl here are familiar with the value of the audioque... if someone was to respond to this particular thread, it would be nice if they were also familiar with the PC18... considering that is the question at hand, and if they were familiar with the PC18 they would also know the value of it (or a quick google search at least) and it is a 250-300$ sub, not a 700-900 sub
  13. spencer321

    FS: RD Alpha 18" D2

    why must you be so far away! not lookin for any kinda trade by chance are ya?
  14. spencer321

    trading my hdc312 for a precision PC18DS, bad idea?

    no **** sparky, you point me where i can get one for 250$ and i'm all over it, or for that matter, if you can show me where i can get a nightshade, death penalty, dc level 5, or hell even an xcon 18 in a straight up trade for a hdc312 than by all means show me the way. I've been doing this for a while, im just not familiar with THIS particular subwoofer
  15. anyone have any experience with these subs, i just figure going from a 12 to an 18, its gotta be louder, but i've had an itch to go bigger for a long time so i don't wanna jump the gone on some garbarge that i'll never be able to get rid of
×