Jump to content


jeeper2269

Member
  • Content Count

    267
  • Joined

  • Last visited

  • Feedback

    0%
  • Country

    United States

About jeeper2269

  • Rank
    Senior VIP Member
  • Birthday 05/16/1979

MORE INFO

  • Location
    Somewhere, OR
  • Interests
    wheelin

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. I spliced into the dome light on my 2007 Jeep and ran led trailer lights on each side facing out and downward, by the side steps. When I did one side, it worked fine and turned off when the dome light turned off. Now, I did the other side and they turn off when the dome light is off, but they stay on when the ignition is on. They are ran in parallel. did something ground out somewhere? or is one of the wires backward?
  2. jeeper2269

    Smaller better sub and box setup than FI for Jeep?

    Depends on what kind of car. But I had this built for to fit where the rear single passenger seat folded up in my 2018 f150. What about two better tens
  3. jeeper2269

    Smaller better sub and box setup than FI for Jeep?

    Really? i totally thought there was something out there that would perform better in a smaller box with that much power. I have not personally heard one, but many have raved about the JL w7 in stealth boxes. I know they are expensive though.
  4. jeeper2269

    Smaller better sub and box setup than FI for Jeep?

    Here’s some pics of how big it is.
  5. I have an 07 Jeep Wrangler Unlimited 4 Door and the current box has an FI 12 “Q”. The box is pretty big and came out of my F150 I sold. I just upgraded the amp to a Teramps md3000. Sounds great, however, I am wondering if I can maybe sell the current box and sub and do a smaller encloser, with a different sub that would be best matched to the amp. Any ideas?
  6. Perfect. Thank you
  7. jeeper2269

    Amps are staying on.....???

    I recently made a trip in my Jeep and took out the speaker box that had the amp mounted to it. So, I unscrewed the amp, pulled the speaker wires and removed the sub box. I left the amp (teramps md3000) still wired, laying down under the back seat. This morning I found the Jeep battery dead. So, I figured out that both of my amps are staying on when I turn the Jeep off. What is happening?
  8. jeeper2269

    How do you guys get 1/0 gauge wire into amps?

    I took the splice out and ran one of the cables direct. Boom, it hits good. However, I do notice some of the lower bass lines in songs not picking up.
  9. Will these be durable/reliable ?
  10. I have a Jeep Wrangler Unlimited and want to install some LEDs (2 each side) facing down on the side steps. And some inside, maybe a couple on the floor on each side of the cab and a couple on each side of the roll bar. Which ones are good quality you guys use ?
  11. jeeper2269

    How do you guys get 1/0 gauge wire into amps?

    Guess the easiest way is to just take the splice out and see
  12. jeeper2269

    How do you guys get 1/0 gauge wire into amps?

    Will this work?
  13. jeeper2269

    How do you guys get 1/0 gauge wire into amps?

    Okay, that might make sense. Since I had to split the RCAs. Explanation - head unit is a pioneer AVH-211EX The deck only has two pre-amp outputs, so,, I had to split the RCAs from the four channel amp to the monoblock
  14. jeeper2269

    How do you guys get 1/0 gauge wire into amps?

    I may just have an extra PAC. Now I am thinking it’s the RCA setup
  15. jeeper2269

    How do you guys get 1/0 gauge wire into amps?

    Okay, that might make sense. Since I had to split the RCAs. Explanation - head unit is a pioneer AVH-211EX The deck only has two pre-amp outputs, so,, I had to split the RCAs from the four channel amp to the monoblock
×