Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Equipment
Subwoofers
need some advice....for powering my subs
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="DeathGrind" data-source="post: 6445489" data-attributes="member: 616341"><p>Hello Everyone! I need some advice for powering my subs.</p><p></p><p>I just purchased a JL Audio CS210RG-W3v3-2.</p><p></p><p>Technical Specification</p><p></p><p>* Sensitivity: 85 dB</p><p></p><p>* RMS Power Range : 200 - 1000 Watts</p><p></p><p>* Peak Power Handling: 2000 Watts</p><p></p><p>* Impedance: 2 Ohm</p><p></p><p>* Low Frequency response: 25 Hz</p><p></p><p>* High Frequency Response: 250 Hz</p><p></p><p>* Diameter: 10 Inch</p><p></p><p>Link for JL Audio CS210RG-W3v3-2:</p><p></p><p><a href="http://mobile.jlaudio.com/products_enclosures.php?menu=9&amp;prod_id=424" target="_blank">http://mobile.jlaudio.com/products_enclosures.php?menu=9&amp;prod_id=424</a></p><p></p><p>I have a PPI A404 amp. Would this amp be enough to run the subs? I was looking through the PPI A404 manual and couldn't seem to find anything about running the amp at 2 ohms mono. I don't know very much about ohms and what not.</p><p></p><p>Link for PPI A404 manual:</p><p></p><p><a href="http://www.directeddealers.com/manuals/og/precision_power/Precision_Power_Ax400_Owners_Manual.pdf" target="_blank">http://www.directeddealers.com/manuals/og/precision_power/Precision_Power_Ax400_Owners_Manual.pdf</a></p><p></p><p>I have another PPI amp in my storage. Not sure what it is but I pretty sure it is a A600, A300 or a A204. I'll know what it is when I make a trip to my storage a few hundred miles away in the next few days. I do recall it being a 2 channel amp.</p><p></p><p>Anyway I have the PPI A404 sitting right next to me. Would this amp be enough to power my subs i just purchased?</p><p></p><p>I read that using the PPI A404 for subs is almost a waste, since it has such nice and clean mids and highs.</p></blockquote><p></p>
[QUOTE="DeathGrind, post: 6445489, member: 616341"] Hello Everyone! I need some advice for powering my subs. I just purchased a JL Audio CS210RG-W3v3-2. Technical Specification * Sensitivity: 85 dB * RMS Power Range : 200 - 1000 Watts * Peak Power Handling: 2000 Watts * Impedance: 2 Ohm * Low Frequency response: 25 Hz * High Frequency Response: 250 Hz * Diameter: 10 Inch Link for JL Audio CS210RG-W3v3-2: [URL="http://mobile.jlaudio.com/products_enclosures.php?menu=9&prod_id=424"]http://mobile.jlaudio.com/products_enclosures.php?menu=9&prod_id=424[/URL] I have a PPI A404 amp. Would this amp be enough to run the subs? I was looking through the PPI A404 manual and couldn't seem to find anything about running the amp at 2 ohms mono. I don't know very much about ohms and what not. Link for PPI A404 manual: [URL="http://www.directeddealers.com/manuals/og/precision_power/Precision_Power_Ax400_Owners_Manual.pdf"]http://www.directeddealers.com/manuals/og/precision_power/Precision_Power_Ax400_Owners_Manual.pdf[/URL] I have another PPI amp in my storage. Not sure what it is but I pretty sure it is a A600, A300 or a A204. I'll know what it is when I make a trip to my storage a few hundred miles away in the next few days. I do recall it being a 2 channel amp. Anyway I have the PPI A404 sitting right next to me. Would this amp be enough to power my subs i just purchased? I read that using the PPI A404 for subs is almost a waste, since it has such nice and clean mids and highs. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Equipment
Subwoofers
need some advice....for powering my subs
Top
Menu
Home
Refresh