Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Basic Anplifier Problems, Distortion and More,Please Help!
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="dylanmurphy23" data-source="post: 8261188" data-attributes="member: 661028"><p>Okay so a few months ago I changed amps from an MTX amp that came with my Dual 12 inch MTX Terminators. I switched to a BOSS R6002 1200 Watt Amp (2 Channel). After installing this amp I noticed that my subs were noticeably quitter, less of a bang and they distort and the amp goes into protection mode. I've been reading online to try to find a solution to this and all ive been seeing is stuff about the ohms. My subs are 2 Ohms and the amp is 4ohms but it also says 2 on it, I don't know which is it I will post a link below. I have these subs bridged and I was wondering if this is a stable ohm load. I'm not very knowledgeable on this stuff so if someone could break it down for me that would be nice.</p><p></p><p>I really don't know how well I explained this, but I hope someone can help me out! //content.invisioncic.com/y282845/emoticons/frown.gif.a3531fa0534503350665a1e957861287.gif</p><p></p><p>Link to Amp Specs. and ill also post my subs.</p><p></p><p><a href="http://www.onlinecarstereo.com/CarAudio/p_32913_Boss_Audio_R6002.aspx" target="_blank">Boss Audio R6002 RIOT 1200W 2-Channel MOSFET Power Amplifier with Remote Subwoofer Level Control at Onlinecarstereo.com</a></p><p></p><p>It says max bridge 4 ohms, does that mean I cannot use this amp with my 2 ohm subs?</p><p></p><p>My subs</p><p></p><p><a href="http://www.onlinecarstereo.com/CarAudio/p_19669_MTX_Terminator_TNP212D.aspx" target="_blank">MTX Terminator TNP212D Amplified Bass System With Two 12" Terminator Subwoofers In a Sealed Enclosure at Onlinecarstereo.com</a></p></blockquote><p></p>
[QUOTE="dylanmurphy23, post: 8261188, member: 661028"] Okay so a few months ago I changed amps from an MTX amp that came with my Dual 12 inch MTX Terminators. I switched to a BOSS R6002 1200 Watt Amp (2 Channel). After installing this amp I noticed that my subs were noticeably quitter, less of a bang and they distort and the amp goes into protection mode. I've been reading online to try to find a solution to this and all ive been seeing is stuff about the ohms. My subs are 2 Ohms and the amp is 4ohms but it also says 2 on it, I don't know which is it I will post a link below. I have these subs bridged and I was wondering if this is a stable ohm load. I'm not very knowledgeable on this stuff so if someone could break it down for me that would be nice. I really don't know how well I explained this, but I hope someone can help me out! [IMG]//content.invisioncic.com/y282845/emoticons/frown.gif.a3531fa0534503350665a1e957861287.gif[/IMG] Link to Amp Specs. and ill also post my subs. [URL="http://www.onlinecarstereo.com/CarAudio/p_32913_Boss_Audio_R6002.aspx"]Boss Audio R6002 RIOT 1200W 2-Channel MOSFET Power Amplifier with Remote Subwoofer Level Control at Onlinecarstereo.com[/URL] It says max bridge 4 ohms, does that mean I cannot use this amp with my 2 ohm subs? My subs [URL="http://www.onlinecarstereo.com/CarAudio/p_19669_MTX_Terminator_TNP212D.aspx"]MTX Terminator TNP212D Amplified Bass System With Two 12" Terminator Subwoofers In a Sealed Enclosure at Onlinecarstereo.com[/URL] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Basic Anplifier Problems, Distortion and More,Please Help!
Top
Menu
Home
Refresh