Assuming the sub is 2ohm/coil ( ), then yes, you can do it either way. Usually it is easier to just wire the coils in series and bridge the amp.Originally Posted by Depression
Assuming the sub is 2ohm/coil ( ), then yes, you can do it either way. Usually it is easier to just wire the coils in series and bridge the amp.Originally Posted by Depression
thank you Very much
ima get prolly some kinda 700 watt mono 2 ohm amp for the RE SE 12'' i want.
92 Plymouth Colt
Alpine 9811 deck
Alpine 5-1/4 speakers w/ silk dome tweeters
Planet Audio P110 10" Sub in ported box
PPI 240 2-way amp
Okay just lost my whole nicely written post.
Okay my question is can i run a Audiobahn alum10q with an aura amp. the sub is 6ohm dvc. the amp can run 160rms at 4ohm. could someone let me know if i can hook up bot voice coils or not off this amp? all info is appreciated!
amp info-
S/N @ 4ohms: >90dB
Frequency response: 20Hz-20KHz min
Channel separation: min 60dB
Slew Rate: 60V/usec
Damping factor: 60
Continuous Power Output class AB
RMS power <0.06% [email protected] 4 ohms: 50 x 4
RMS power <0.1% [email protected] 2 ohms: 80 x 4
RMS power <0.1% [email protected] 4 ohms: 160 x 2
Active crossover: continuous (HP/LP/Full)
Crossover frequencies: full/50-250Hz
Cant find info transfer on the sub.
Thanks
Danny
Who-Danny Allen 18 years old
Ride-89 Chevy Stro'
Important stuff
Stereo-Alpine 7977
front-Infinity Reference 6000cs 6.5" components
rear-infinity 4x6 plate speakers
amps-directed 1200/5 (for comps)and a directed 1100d (for sub)
sub-Re Se 12"
wiring-Scosche 4ga have 2ga ready to install
AIM-nitrpyro
Yahoo-nitropyro666
is this possible ?? check attachment , its a 4 channel amp , bridged to 2 channel, i know i can connect each channel to a Voice coil, but i need a 2 ohm load for more power out of the amp.
i know its better to wire to each coil, and set the gain equally, but i still wanna if its possible or not . thnx
Okay i take it that wasnt to help me. or was it? my main concern was the 6 ohm rating on the sub. And if i could run it and not push it full power? sry im lost once again been out of the scene to long
Thanks
danny
Who-Danny Allen 18 years old
Ride-89 Chevy Stro'
Important stuff
Stereo-Alpine 7977
front-Infinity Reference 6000cs 6.5" components
rear-infinity 4x6 plate speakers
amps-directed 1200/5 (for comps)and a directed 1100d (for sub)
sub-Re Se 12"
wiring-Scosche 4ga have 2ga ready to install
AIM-nitrpyro
Yahoo-nitropyro666
how does the rca wires goto the deck to the amp
how to you tell if the amp is fired
In the diagrams it shows all the wiring ending up to one source. Even if there are two subs there always turns out to be only one set of 1 pos and 1 neg. So does that mean that you can bridge the amp to that one set to as long as that amp handles that final impedance in that last set?????
hey everyone. i was wondering if i could get some wiring help. i'm getting 2 kicker 12" L7's and a vented box to mount them in and right now i have a small amp (punch p2002). i was wondering if anyone could help me with the wiring of these subs? i plan on selling this amp and getting a more powerful one eventually. please help?? thanks to everyone's input.
ok, how about a DVC 8ohm sub at 2 ohms? i doubt it, i think you can get it to 4 ohms with no problem.
i do have 2 of them, so maybe i can drop it to 2 ohms with a mono amp?
so, can i get 2 ohms from a single DVC 8ohm driver?
OR
can i get 2 ohms from (2) DVC 8ohm driver?
this was not listed in this thread yet.
is it 64...or 32 ohms. i think 32Originally Posted by DBfan187
you could also wire 2 8ohm DVC's to an 8 ohm load.
NEED A BOX DESIGN? PM ME
HEAD UNIT
860mpACTIVE FRONT STAGE
JBL GTO75.4 II
RE 6.5
VIFA XT25 ring radiator 1"
SUB STAGE
ega 1400d
3HP FI
STOLEN
actually 2 DVC 8 ohms can be wired to 2, 8, or 32
MdOiDcEtRaAtToOrR
1996 Chevrolet Impala SS 14.5 @ 94
1967 Chevrolet Camaro 18.4 @ 74
mind putting up a lil diagram?
ill be lookin for a 2ohm ~300w amp for my buddy now
thanks guys!
Bookmarks