voicecoil wiring options

[_DjScrew_]

what happened to the RF pics?

[Call_it_done]

1 JL 12w6v2 D4

Diamond Audio 600.2 with the following ratings:

RMS Output Power
150W x 2 @ 4 Ohm Stereo
300W x 2 @ 2 Ohm Stereo
600W x 1 Bridged @ 4 Ohms
# Freq Response: 10Hz-50KHz
# Signal-to-Noise Ratio: 102dB
# THD: 0.03%
# Channel Separation: 80dB
# Length: 17"
# Width: 12"
# Height: 2.75"

Can I get 600 to the 12w6? I don't think so.

[crazy4life]

I cant decide if i'd be better of with a single 15inch d1 sub wired at 2ohms or a d2 wired at 1 ohms. Thoughts?

[Deusle]

I cant decide if i'd be better of with a single 15inch d1 sub wired at 2ohms or a d2 wired at 1 ohms. Thoughts?

wellit depends, if its a power hungry sub get the d2 so you can get a 1 ohm stable amp

[Oneinthesac]

ok so can anyone show me where i can see a wiring diagram of a quad 1ohm coils setup for 1ohm load

[NightLight03]

I went to the Rockford Wizard on the site for help..

well.. I have Three 4 ohm DVC subs. the wiring on the diagram doesn't help.. are they saying to hook one coil to itself? or to hook across from one Coil's + to the other coils -?

sorry if thats confusing, I'll take some pics.. but I did get a result of 2.6 ohms.

But I want to double check my wiring.

http://www.rockfordfosgate.com/rftec...3&woofer_imp=4

[loopkiller]

I went to the Rockford Wizard on the site for help..

well.. I have Three 4 ohm DVC subs. the wiring on the diagram doesn't help.. are they saying to hook one coil to itself? or to hook across from one Coil's + to the other coils -?

sorry if thats confusing, I'll take some pics.. but I did get a result of 2.6 ohms.

But I want to double check my wiring.

http://www.rockfordfosgate.com/rftec...3&woofer_imp=4

That link is very clear to me. Is there a certain part of it that you don't understand? Each woofer will show an 8ohm load and then with 3 x 8 ohm woofers wired in parallel, that is 8/3=2.66ohm.

[O2JR]

Hello everyone. I have a couple of questions, and I was wondering if u guys can help me. I have these subs, 2:

http://www.amazon.com/Kicker-CompVR-...2689236&sr=8-1

Kicker 12" 4ohm DVC. So I was wondering if I got 2 of these amps one for each sub ofc, I would get 400 RMs out of those subs theorically.

http://www.crutchfield.com/p_2068ZX4...-1.html?tp=115



In the diagram I have 2 ohm, So I would get the actually 400 RMS that the amp has theorically. Would these amps would work just fine. I won't have problems with burn fuses or overheating the amp? ... Thx in advance all...peace..

[sgreg7908]

i need help just wired up two jl 6*9 and the highs r the only thing coming on

[blazron22z]

i have 3 mmats 3.0 15" and a rockford fosgate t20001bd how do i wire the subs to get the most out of my amp??

[blazron22z]

there d4

[dman4486]

i have 3 mmats 3.0 15" and a rockford fosgate t20001bd how do i wire the subs to get the most out of my amp??

http://www.the12volt.com/caraudio/wo...igurations.asp

[drifterz73]

hi got a lil question... i have one 12" audiobahn immortal qvc 2ohm wired to 2ohm
and a a rockford p3 12" dual 4ohm wired to 2ohm..
the amp is a audiobahn a2300hct 2 channel can i wire these subs to 1ohm or should i just buy another rf p3 .... the amp is stable to 1ohm.... any comments suggestions....thanx in advance...

[dman4486]

hi got a lil question... i have one 12" audiobahn immortal qvc 2ohm wired to 2ohm
and a a rockford p3 12" dual 4ohm wired to 2ohm..
the amp is a audiobahn a2300hct 2 channel can i wire these subs to 1ohm or should i just buy another rf p3 .... the amp is stable to 1ohm.... any comments suggestions....thanx in advance...

don't mix subs

[drifterz73]

ok so which sub would you recommend running then the a.b. or rf... and buy another p3