chris you gonna run the ZX2500.1 @ .5 ohms? ohh and you need to change the metering to your newest scores with the new box
chris you gonna run the ZX2500.1 @ .5 ohms? ohh and you need to change the metering to your newest scores with the new box
that was under the dash but letz see if i can get it on the T.L soon then i'll post it up
VEHICLE 2004 Nissan Xterra
HEAD UNIT Audiovox PRV1510DTV
WIRING ALL Kicker Wiring
MIDS&HIGHS 3- sets of Kicker RS6.5
MID AMP Kicker KX650.4
SUBWOOFERS 4 Kicker L7D4
BASS AMPS 2- Kicker KX2500.1
SIGNAL PROCESSOR Kicker KQ30
POWER 2- kinetic 1800
ref. nVRuckus,iamamp3pimp,NeillBarber,dkmesa,Devin_9_20 04,Kenny Pollock
ok simple question...didnt want to make another thread. Im getting a D4 sub and want to wire it to 2ohms. There are four sets of terminals...do I only need to use two sets...or do I wire them neg-neg, pos-pos, and then the same to the other two sets?
Pioneer AVH-P4400BH
Alpine pdx 1.600
Alpine pdx 4.100
18in obsidian
[email protected]
4x kenwood kfc-1693ps...
Refs: 5o4m6, assman, basschild, BIG4EVER, bonesninja, bjfish11, canyouhearmatt, Coolwazabi, cdf294, chaunb3400, DownSouth954, here to buy, squeak12, THXdts, jmanpc, JBloud47, jk32sho, johnson, Louisiana_CRX, Mike465, nismos14, pitbull12887, ProblemHouston, Fear of Theive, farmerehsan, rollerdj, valter, WaTTsLOk187
^^
Pioneer AVH-P4400BH
Alpine pdx 1.600
Alpine pdx 4.100
18in obsidian
[email protected]
4x kenwood kfc-1693ps...
Refs: 5o4m6, assman, basschild, BIG4EVER, bonesninja, bjfish11, canyouhearmatt, Coolwazabi, cdf294, chaunb3400, DownSouth954, here to buy, squeak12, THXdts, jmanpc, JBloud47, jk32sho, johnson, Louisiana_CRX, Mike465, nismos14, pitbull12887, ProblemHouston, Fear of Theive, farmerehsan, rollerdj, valter, WaTTsLOk187
Pioneer AVH-P4400BH
Alpine pdx 1.600
Alpine pdx 4.100
18in obsidian
[email protected]
4x kenwood kfc-1693ps...
Refs: 5o4m6, assman, basschild, BIG4EVER, bonesninja, bjfish11, canyouhearmatt, Coolwazabi, cdf294, chaunb3400, DownSouth954, here to buy, squeak12, THXdts, jmanpc, JBloud47, jk32sho, johnson, Louisiana_CRX, Mike465, nismos14, pitbull12887, ProblemHouston, Fear of Theive, farmerehsan, rollerdj, valter, WaTTsLOk187
what are my options with two DvC2ohm subs
Hi
I made a box for 4 sub 2 in front and to up, the 2 sub that goes up will be inverted, the subs are 4ohm SVC, do i have to invert the phase of the up subs, and how can i do that,
PS: i need a 4ohm load.
Thanks
Car: 2008 Lincoln Navigator
HU: evaluation the options...
Front Spk: evaluation the options...
Amp: evaluation the options...
Sub: evaluation the options...
i have a question guys and i apriciate if you can answer it , i bought 2 kicker L5's 2 ohm's and my eletrionic store put the in the kicker enclosure box , it sounds like the guy knows what he was doing.... but my question should be if the subs are 2 ohms can they be configured to be 4 ohms or other methods???
this is what happend i wanted the 06DS12L5-2 (2 OHM) but the ones they had were the 4 ohm version ( the box tho) so they just took out the 4 ohm subs and put the 2 ohms subs (L5's) but my question is how do i know if the guy pre wired it right?????
is it possible to wire 3-DVC 8 ohm subs down to a final load of 4ohms? Im thinking 2- DVC 8 ohm subs can be wired down to 4 ohms. Also what will be all the ohm possibilities for 4-DVC 8 ohm subs
all in all im trying to see how many DVC subs is possible to be ran at 4 ohms as a final load?
thanks
My Goal
How many different ways to wire 2 - dual 4 ohm ? (the maw12s)
if you have 2 dual voice coil 2 ohm subs and wire them to two ohms, wont you only be using one ohm?
what are my options for 2 - Quad 1's
2009 Nissan Sentra
REFS - kickerlivinloud, stevew007, jellyfish420, Packerfan, FinalWolf, Bumpncarstereo, subingncali, bigmurf127, 1loudsuv, NhustlaR, violentrapture, toaster, thunder9500, Ecko072Unltd, kickinaudio, LivinLife, PV Audio, JDizzle, 5thgenaccord, krouchchocolate, duece212, PBateman, 22mountaineer, ProjectPechkin
I would drag my cock through a mile of broken glass just to hear her fart through a walkie talkie.
Lemme get this straight. If I were wire up two, 2Ohm DVC subs like shown in the attached diagram, I will have a 2-Ohm load. I got that.
Here's my question:
If each sub is rated at 1000W RMS, then I could run the subs off one channel on a 2000x1 amp and each sub would get about 1000W each, yes?
Also, are there any concerns about running two, 2Ohm DVCsubs on a .5Ohm load versus a 2Ohm load as a daily driver off one channel (provided the amp is stable at the respective Ohm)?
Good job, America, you just elected a Socialist to be the next president.
"Sabrina, don't just stare at it, eat it!"
Refs:
Teamquakecelica (bought from), Kfra315 (sold to)
so wich option it best for a quad voice coil audiobahn awis12p sub on a 4 channel amp bridged?
Last edited by soda_cube; 05-28-2007 at 07:33 PM. Reason: Wrong amp channel posting
Bookmarks