Closed Thread
Results 1 to 3 of 3

Reload Thread: Wiring subs dvc 4 ohm cant run less than 2ohm

  1. #1
    jrmax's Avatar
    jrmax is offline Senior VIP Member



    Join Date
    Dec 2001
    Location
    oklahoma
    Age
    28
    Posts
    255
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Wiring subs dvc 4 ohm cant run less than 2ohm

    Okay my amp aint the greatest it is the crunch i have been griping about and I dont want to run it too low of an ohm like 2 at the lowest and I sort of need it at two to push my dvc 12 type R's(dvc 4ohm). 300 watt rms on the subs the amp is 4 channels and 125 watt per channel and if i wire it down to 2 ohm it should be 250 per channel. Realisticly I would be perfectly happy if it put out 175-200 watts per channel. Anyway if I run 1 channel to one voice coil then what ohmage would I be at I NEED TO NO BAD IF YOU KNOW PLEASE DONT HOLD OUT ON ME! Would this cheap crunch amp die under the stress? What would it be called if i wired it like this is it possible!??! Anyway please help me as best you can I need answers to all my ?'s







  2. #2
    EPanther99's Avatar
    EPanther99 is offline Senior VIP Member



    Join Date
    Feb 2002
    Location
    Elizabethtown KY
    Age
    33
    Posts
    306
    Post Thanks / Like
    Mentioned
    0 Post(s)
    well i looked up the specs for crunch amps and all of them are only stable to 4 ohms so it would break under the pressure i think. if you wanted to get a 4 ohm mono load you can wire each speaker to 8ohms and then each one of those together to make a 4 ohm mono load .



    HU: Pioneer Premier P-720
    Front: JVC 2 way 6.5" component system
    Rear: Kenwood KFC-1687
    Subs: (2) 2002 Kicker 15" L7's
    Amps: (2) Infinity Beta Digital 300's
    (2) 1 farad Stinger Power Caps
    (2) 1 farad Monster Cable Monster Caps

  3. #3
    Unregistered's Avatar
    Unregistered Guest



    **** it do you have a diagram to explain




Closed Thread

Similar Threads

  1. Wiring Subs @ 1 ohm help
    By rumdada in forum Enclosure Design & Construction Help
    Replies: 12
    Last Post: 04-14-2011, 12:03 PM
  2. Wiring subs different ohm?
    By slapperz in forum Subwoofers
    Replies: 5
    Last Post: 10-12-2009, 12:19 AM
  3. wiring subs and ohm load
    By tigerh4rf in forum Wiring, Electrical and Installation Help
    Replies: 4
    Last Post: 04-08-2009, 05:25 PM
  4. wiring 2 dvc 6 ohm subs to mono amp
    By achallie in forum Amplifiers
    Replies: 11
    Last Post: 12-16-2006, 11:17 AM
  5. wiring three DVC 2 ohm subs
    By talon2nr7588 in forum Wiring, Electrical and Installation Help
    Replies: 5
    Last Post: 10-30-2006, 12:25 PM

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may post attachments
  • You may edit your posts
1e2 Forum