I am going to run 2 sets of Polk Momo MM6 comps off of a 2 channel amp, each speaker is 4 ohms, so each channel of my amp will see 2 ohms right? Or does the crossover do something wierd to make my amp see 4 ohms?
I am going to run 2 sets of Polk Momo MM6 comps off of a 2 channel amp, each speaker is 4 ohms, so each channel of my amp will see 2 ohms right? Or does the crossover do something wierd to make my amp see 4 ohms?
the old school MM6's? sell me a set
each set is 4 ohms. are you running both sets of crossovers?
http://www.polkaudio.com/caraudio/specs/recent/mm6/
1994 Thunderbird
JVC KD-AV7010
Alpine 6x9 3-ways
Pioneer 6x8 3-ways (rear)
JVC CH-X1500 12-disc MP3 Changer
Alpine Type X 12" 2 cubes @ 30hz
MTX 404 runs the inside
MTX 1501d runs the X
Optima G75/25 RT up front
2x Optima G31 YT in the trunk
200a EA HO Alt (1/0 Big 3)
ALL MY WIRE IS WELDING CABLE
DO NOT SEND ME ANYTHING USING UPS. I WILL NOT DEAL WITH THEM EVER AGAIN
OFFICIAL FEEDBACK THREAD
your amp will see 4ohms, if your comps where 2ohms then it will see a 2ohm load
if your using 2 4ohm speakers then yes it will see 2ohm a ch
TEAM420
TEAM CACTUS SOUNDS
TEAM MAXXSONICS
TEAM XSPOWER
TEAM DC AUDIO
SS 1-2 3rd PLACE 2007 INDY "REGIONALS"
SS 1-2 1ST PLACE INDY AND 2008 NATIONAL CHAMPION.
http://www.alphadamp.com
^^^^what??????
he said he was using 2 sets of speakers (4ohm each ) on a 2 ch that will give him a 2ohm load each ch
TEAM420
TEAM CACTUS SOUNDS
TEAM MAXXSONICS
TEAM XSPOWER
TEAM DC AUDIO
SS 1-2 3rd PLACE 2007 INDY "REGIONALS"
SS 1-2 1ST PLACE INDY AND 2008 NATIONAL CHAMPION.
http://www.alphadamp.com
Here is what I will be doing, on each side of the car will be 1 tweet and 1 mid, plugged into 1 crossover. thats 2 tweets, 2 mids, and 2 crossovers. the left channel of my amp will go to 1 crossover, which goes to 1 tweet and 1 mid, same with the right channel. What I want to know is if each individual speaker is 4 ohms, my amp will run at 2 ohms right? I just want to make sure that my amp will see 2 ohms, because my amp does 160x2 at 2 ohms, but it only does 80x2 at 4 ohms, and I would need something better if it saw 4 ohms.
if they are bi amp capable then bi amp them and get 2 ohms. ask t3 to make sure
sold to: Johnny Law.Lulz/Worstenemy453,Pumkinman, j1b1e1, DexterMoped, miyagi gboo559,CSU87,nate2587, MichaelLane, SmLLySack. MR_Imperial, Herrrerra, ltr450racer690, 05fronty bought from: TripleB45, bigwheel15, (kroid77 but never recieved..)
helping noobs daily PM me
Do you mean get two mono amps that do 150 watts at 4 ohms, one amp for each door?
edit: wait thats not what you mean, hang on i'll look up bi-amping.
Bookmarks