Closed Thread
Results 1 to 13 of 13

Reload Thread: Component Speaker set up and questions

  1. #1
    JettaGLI's Avatar
    JettaGLI is offline Senior VIP Member



    Join Date
    Sep 2005
    Location
    PDX
    Age
    37
    Posts
    171
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Component Speaker set up and questions

    I currently have JL VR comps up front and coax in the rear, 6.5" all the way around. I want to get rid of the rear speakers, as I like the way things sound better without them.

    My subs are JL Audio 12w6v2's (2 of them) and a 1000/1 JL amp.

    My mids amp is a JL 300/4

    Keep in mind I am sticking with nothing but JL here, flame away, but I like em', and have since way back in the day!

    Quesiton 1- Would the ZR line that is coming out overpower my subs, meaning, are they more meant to couple with the w7's? Should I just go ahead and get the XR 6.5" comps set as a better match for my subs?

    Question 2- In my front speaker location, there is about 6-8" of space between the speaker and the actuall speaker grill/door pannel. It seems to me that this would allow a lot of the sound to escape the car, and end up in the actuall door pannel. My stock speakers had a rubber surround around them that butted up to the acutuall grill on the door. SHould I do this with my comp set as well? Or would it be better to build a baffle that extends the speakers out to the door pannel's speaker grill... or be just fine the way it is?

    I will bridge the 300/4 to 150 watts x2, so the power will be there for no matter what speakers I go with.







  2. #2
    goon's Avatar
    goon is offline Junior Member



    Join Date
    Oct 2005
    Location
    Florida
    Age
    29
    Posts
    12
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Component Speaker set up and questions

    I'm not an expert, but if you have 6-8" of space between the speaker and the grill you are losing sound. The main concern there is that you will get poor imaging. I would get a mount to minimize that space. try it an see if it sounds better, which it should, if you don't like put it back the way it was.




  3. #3
    JettaGLI's Avatar
    JettaGLI is offline Senior VIP Member

    Threadstarter


    Join Date
    Sep 2005
    Location
    PDX
    Age
    37
    Posts
    171
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Component Speaker set up and questions

    Quote Originally Posted by goon
    I'm not an expert, but if you have 6-8" of space between the speaker and the grill you are losing sound. The main concern there is that you will get poor imaging. I would get a mount to minimize that space. try it an see if it sounds better, which it should, if you don't like put it back the way it was.

    What about the rubber surround thing?




  4. #4
    goon's Avatar
    goon is offline Junior Member



    Join Date
    Oct 2005
    Location
    Florida
    Age
    29
    Posts
    12
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Component Speaker set up and questions

    Just to make sure i get this right. Instead of the speaker being mounted on the door pannel iw was mounted on the grill with a rubber surround? Like I said before, just play with it. try different mountings and see which one you will like the best, after all you will the one listening to them.




  5. #5
    JettaGLI's Avatar
    JettaGLI is offline Senior VIP Member

    Threadstarter


    Join Date
    Sep 2005
    Location
    PDX
    Age
    37
    Posts
    171
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Component Speaker set up and questions

    I don't know what I was thinking when I said the above comment on bridging the amp. I forgot that bridging means MONO.

    So I guess I will need to get a 300/2 to get full power.




  6. #6
    JettaGLI's Avatar
    JettaGLI is offline Senior VIP Member

    Threadstarter


    Join Date
    Sep 2005
    Location
    PDX
    Age
    37
    Posts
    171
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Component Speaker set up and questions

    Quote Originally Posted by goon
    Just to make sure i get this right. Instead of the speaker being mounted on the door pannel iw was mounted on the grill with a rubber surround? Like I said before, just play with it. try different mountings and see which one you will like the best, after all you will the one listening to them.

    Wrong, the speaker was mounted to the door frame, not the pannel. Then there was a rubber surround that was connected the speaker to the door pannel grill.

    For all you installers, it is a VW Jetta. If that helps any.




  7. #7
    goon's Avatar
    goon is offline Junior Member



    Join Date
    Oct 2005
    Location
    Florida
    Age
    29
    Posts
    12
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Component Speaker set up and questions

    No, I'm prett sure you can bridge the amp. But because it's a 4 channel amp you will be pulling more current than if you went with a 2 channel. The 4 channel should work ok, just make sure the impedence matches.




  8. #8
    Join Date
    Mar 2005
    Location
    Where you live (Ex. Los Angeles, CA)
    Posts
    2,264
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Component Speaker set up and questions

    it's pretty hard to overpower a properly installed W6v2 with any set of mids... and it's always good to have more headroom...

    I would say go as high as you can if you don't have a budget in the JL line if you *have* to use JL ... much better high end out there on a $$$ ratio but i can understand the attachment to a brand.

    in conclusion, ZR is fine =]



    Owner of Post 22,222 in THE Thread.

  9. #9
    JettaGLI's Avatar
    JettaGLI is offline Senior VIP Member

    Threadstarter


    Join Date
    Sep 2005
    Location
    PDX
    Age
    37
    Posts
    171
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Component Speaker set up and questions

    Quote Originally Posted by goon
    No, I'm prett sure you can bridge the amp. But because it's a 4 channel amp you will be pulling more current than if you went with a 2 channel. The 4 channel should work ok, just make sure the impedence matches.

    I know I can bridge the amp, but you can't bridge and get stereo can you? Remember, these are for front component speakers.




  10. #10
    JettaGLI's Avatar
    JettaGLI is offline Senior VIP Member

    Threadstarter


    Join Date
    Sep 2005
    Location
    PDX
    Age
    37
    Posts
    171
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Component Speaker set up and questions

    Quote Originally Posted by twoohfour
    it's pretty hard to overpower a properly installed W6v2 with any set of mids... and it's always good to have more headroom...

    I would say go as high as you can if you don't have a budget in the JL line if you *have* to use JL ... much better high end out there on a $$$ ratio but i can understand the attachment to a brand.

    in conclusion, ZR is fine =]

    Thanks!




  11. #11
    954runner's Avatar
    954runner is offline just bumpin my music



    Join Date
    Jul 2005
    Location
    Dallas, TX
    Age
    27
    Posts
    1,034
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Component Speaker set up and questions

    cant you get y splitters on the RCA's? or plug in 2 sets or RCA's? something like that??



    =====================
    ///kyle


    head unit eclipse 8445
    front stage diamond audio m651 components
    sub jl 12w3v2 d2
    amp jbl gto 755.6

  12. #12
    JettaGLI's Avatar
    JettaGLI is offline Senior VIP Member

    Threadstarter


    Join Date
    Sep 2005
    Location
    PDX
    Age
    37
    Posts
    171
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Component Speaker set up and questions

    Quote Originally Posted by 954runner
    cant you get y splitters on the RCA's? or plug in 2 sets or RCA's? something like that??

    Anyone??? I don't know.

    Is it even worth upgrading from the VR to XR?




  13. #13
    JettaGLI's Avatar
    JettaGLI is offline Senior VIP Member

    Threadstarter


    Join Date
    Sep 2005
    Location
    PDX
    Age
    37
    Posts
    171
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Component Speaker set up and questions

    Any suggestions on the upgrade? Should I get rid of the rears, and upgrade to XR comps? Or wait for the ZR Comps to come out?




Closed Thread

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may post attachments
  • You may edit your posts
1e2 Forum