Closed Thread
Results 1 to 4 of 4

Reload Thread: need help

  1. #1
    burningchevy's Avatar
    burningchevy is offline Junior Member



    Join Date
    May 2012
    Location
    alberta canada
    Posts
    4
    Post Thanks / Like
    Images
    2
    Feedback Score
    0
    Mentioned
    0 Post(s)

    need help

    i need help from a profesional sub box desinger.

    im rying to design a sub for my clarion ssw1001 signiture series dvc sub that is runing at 2 ohms

    these are some specs i found on the net but cant find enclosure measurments.

    Enclosure Airspace = 1.0 ft3 net
    Vent = 2.5 diam. x 12.79 long
    Fb = 30Hz F3 = 25.11 Hz
    Max Peak Music Power 2,000 W
    Max Power 1,000 W
    Nominal Impedance 2 or 8 Ohms
    Fs (Hz) 33.5
    Qms 4.27
    Vas (Ft3 / Litre) 0.533 / 15.1
    Mms (grams) 190.7
    Xmax (mm) 24
    Sd (Sq. M) 0.03
    Qes S/P 0.753 / 0.753
    Re S/P (Ohms) 6.4 / 1.6
    Le S/P (mH) 1.517 / 6.067
    Bl S/P (Tm) 18.47 / 9.236
    Qts 0.64
    2.8 V SPL S/P (dB) 80.66 / 87.75
    no S/P (%) 0.073
    Vd (ft3 / Liter) 0.071 / 2.0
    Mounting Depth (mm) 177
    Outside Diameter (mm) 277
    Cutout Diameter (mm) 230

    (ether i dont see the measurements im looking for or im just a little screwed up in the head)
    Attached Thumbnails Attached Thumbnails need help-untitled.jpg  







  2. #2
    smgreen20's Avatar
    smgreen20 is offline phoenixphorum-com



    Join Date
    Apr 2005
    Location
    Lafayette,IN
    Age
    37
    Posts
    1,172
    Post Thanks / Like
    Feedback Score
    1 (100%)
    Mentioned
    0 Post(s)

    Re: need help

    What is it you're after? Sealed,ported? WinISD, manufacture recommened? I run my Clarion SSW1200 in a ported box that's 15% bigger then what's factory recommended. I've built a few boxes for this sub to hear what sounds best and do yourself a favor, use the port diameter that's recommended, it helps control the sub. I thought it a bit small, but every box I built that I used a bigger diameter port, it sounded uncontrolled. I have the factory specs (manual) in the bedroom, but my wife is asleep.




    My install
    http://phoenixphorum.com/viewtopic.php?f=10&t=16998

  3. #3
    smgreen20's Avatar
    smgreen20 is offline phoenixphorum-com



    Join Date
    Apr 2005
    Location
    Lafayette,IN
    Age
    37
    Posts
    1,172
    Post Thanks / Like
    Feedback Score
    1 (100%)
    Mentioned
    0 Post(s)

    Re: need help

    Also, iirc, sealed .75 cf, ported 1.0 cf, but I don't recall the ports dimensions.




    My install
    http://phoenixphorum.com/viewtopic.php?f=10&t=16998

  4. #4
    smgreen20's Avatar
    smgreen20 is offline phoenixphorum-com



    Join Date
    Apr 2005
    Location
    Lafayette,IN
    Age
    37
    Posts
    1,172
    Post Thanks / Like
    Feedback Score
    1 (100%)
    Mentioned
    0 Post(s)

    Re: need help

    OK, I've got the manual now.

    Per factory requirements.
    Sealed: .5 ft^3 net
    Qtc= .721, F3= 45.22 Hz

    Ported: 1.0 ft^3 net
    Vent= 2.5" diam. x 12.79" long
    Fb= 30 Hz, F3= 25.11 Hz

    Hope that's what you were after.




    My install
    http://phoenixphorum.com/viewtopic.php?f=10&t=16998

Closed Thread

Similar Threads

  1. I NEED HELP ..PLEASE!!!!!!!!!!!!
    By crash_n_burn69 in forum General Discussion
    Replies: 5
    Last Post: 01-03-2002, 03:01 PM
  2. Need help with making a selection for box?
    By Shocker28 in forum General Discussion
    Replies: 4
    Last Post: 01-03-2002, 02:58 PM
  3. NEWBIE HERE..need help PLEASE..!!!!!!
    By Tryin2bump in forum General Discussion
    Replies: 2
    Last Post: 12-29-2001, 09:58 AM
  4. Need help on amp for highs and mids
    By liwaj79 in forum General Discussion
    Replies: 1
    Last Post: 12-22-2001, 07:40 AM
  5. need help on my setup
    By <helpme> in forum General Discussion
    Replies: 1
    Last Post: 12-11-2001, 01:28 AM

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may not post attachments
  • You may edit your posts
1e2 Forum