Closed Thread
Results 1 to 4 of 4

Reload Thread: Active setup - Audison Bit One

  1. #1
    BAT284's Avatar
    BAT284 is offline Junior Member



    Join Date
    Jul 2009
    Location
    Baton Rouge, LA
    Posts
    7
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Active setup - Audison Bit One

    Question on the Bit One:

    Can the Bit One accept 2 channels of preamp signal and output that signal to 6 channels (3 sets at different crossover settings)?

    If yes, then if my input voltage is 5 volts each, will that voltage be split to the 6 outputs or will each output voltage be 5 volts or greater?

    I an trying to find if this processor will work for running an active 3-way component speaker system for the front stage. I would like to use the HUs front preamps just for the front stage and save the rear preamps for the back doors (probably a full range speaker or passive 2-way components).

    If this wont work, does anyone know what will. Any options?







  2. #2
    bose301s's Avatar
    bose301s is offline I can break these cuffs



    Join Date
    Apr 2007
    Location
    Durham, NC
    Age
    27
    Posts
    5,974
    Post Thanks / Like
    Images
    11
    Mentioned
    0 Post(s)

    Re: Active setup - Audison Bit One

    Yes, you can take 1 input and split it 3 ways no problem. I know for my DSP6 the voltage also gets split however so you would have a much lower output voltage.



    http://www.klippel.de/download/Nonlin/Klippel_nonlinearity_poster.jpg

    Car System:
    Stock for now

  3. #3
    LaserRed38's Avatar
    LaserRed38 is offline CarAudio.com Veteran



    Join Date
    Nov 2007
    Location
    Bay Area, CA
    Posts
    2,330
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Active setup - Audison Bit One

    Where are you buying it from? The set up is very complicated. I'd get it authorized from a shop and have them walk you through it.



    2005 Escape XLT Sport
    Alpine CDA-9835 - Audison LRx5.1k - Hertz MLK 2 TM - Hertz ML1600 - Hertz HX300
    Audison Wiring - Optima Red Top - Dynamat Extreme
    Refs
    [Bought from] dcmcki, 90accordman, MikeyB, itzme218, redcalimp5, SVT_RELAMPAGO, Johnny_Drama, RollinGTO, Fast1One, tc3k101, ramk1018, Brian_Smith06, John_Pionke, BigOso, TeamPSI, pickup1, PatFitz9, pro-rabbit, oldschoolboomer
    [Sold to] darqnez, tipnitty, Mugatu0, MrChow, nineball, SocialStealth, macq32, .livin.loud., slappinX, GlassEyez, Jeremy M, Honez
    [Traded with] James Bang, MovnZ28

  4. #4
    BAT284's Avatar
    BAT284 is offline Junior Member

    Threadstarter


    Join Date
    Jul 2009
    Location
    Baton Rouge, LA
    Posts
    7
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Active setup - Audison Bit One

    i doubt there is any authorized shop nearby. i do plan on doing a lot of research on active tuning and getting help from someone nearby.

    I have read that the with DSP6 the input voltage does get split to the output voltage. I would like to know if the same gets done with the bit one. if so is a line driver such as the Tru needed. What is the voltage input limits on the bit one. The Audison website and pdf spec sheet for the bit do not give this info. I have sent them an email with these questions.




Closed Thread

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may post attachments
  • You may edit your posts

1e2 Forum