Assuming all speakers in your setup will be driven by external amplifiers, any other benefit to having this feature?
Assuming all speakers in your setup will be driven by external amplifiers, any other benefit to having this feature?
I beleive it adds voltage to your preouts when doing so, correct me if i am wrong.
If you are viewing my profile from SMD, FSC, or d-series.org, then this is the thread with my refs...
Refs: http://www.caraudio.com/forum/showthread.php?t=231239
sq
Kenwood KDC-X889,
Orion 8004, Directed 1500D, SoundSplinter RL-p 15" D2, CDT ES-620 and CDT UP224 upstage kit, BXT RAAMmat (TRUNK) Dynomat Extreme (DOORS & REAR DECK), Stinger 150 Amp Circuit Breaker, Stinger Fused Distribution block, Audiobahn 0 guage power and ground, Audiobahn 4 guage pwr/grnd (amps), 12 guage Rockford Fosgate speaker lines (sub), 15 guage Rockford Fosgate speaker lines (comps), Kicker Interconnects X3 and Optima Yellow Top.

it reduces the heat built up in the deck, and theoretically better sq
The manual for my X-889 says that doing this increases your output voltage and creates less heat with better SQ as a few stated above. I notice a huge difference when I turn it off and on.
No matter how HOT she really is, somebody, somewhere is tired of her *****!
My lugnuts require more torque than you ricers engine makes.![]()
Owner of post 80,000 in The Thread.![]()
My Ride-95 Tahoe 4x4 6" lift and 35's
Headunit- Kenwood Excelon X889
front comps-6.5 in. Boston Pros
rear comps-6.5 in. Pioneer Premiers
Subs-2 12" Alpine Type R 4 ohm DVC
Sub amp- Hifonics Brutus BX1205D
Component amp-Hifonics Zeus Z440
Box-5 cuft. tuned to 32hz.

i know some alpines and kenwoods have this feature....any others?
-jordan-
msn - jeby97@hotmail.com
aim - bumpinking
REFS -
rockingchair69
tirefryr
magick_man
cjj2d
ssj2xxgotenxx

Originally Posted by loserpunk
some clarion units
My Alpine 9827 had that feature. Altought i was using it, it was still running hotter than my Pionner 860mp.
Pioneer deh 860mp
Sub. XXX15 4 cu @ 35hz
Sub amp. orion 2500d
ID Chameleons
UsAmps Merlin MD-22
180 amp HO alt.
Yellowtop.
Big 3.
REF. Starky, iceteebone, wedge, tynee, H2Camaro, jrz126, Jordantyler, theCybe, zachzchw, whoaa, dimebag-1966-20, wj94, AcidicDreams, Flakko, Toxic tuan, ~Magick_Man~, MatthewR6
Ebay Masterme0

Yup, as stated simply... there's less stress on the HU.
nG
http://crunktimes.com/ct/
nG - BSEE

I know you mentioned kenwood already, but my X789 has the feature too. I think the entire(or at least the majority) of the eXcelon lineup have this feature.
-Lurius
Vehicle: 2004 Silverado ECSB 5.3L
Dyno: HP Max = 264.89, Torque Max = 305.25(New #s soon, as well as track times!)
Headunit:Kenwood eXcelon KDC-X789
Front Speakers:Infinity Reference 6010cs
Subwoofers:two Orion 2NT 10"s enclosed within sealed Probox
Subwoofer Amp:Alpine MRV-T757 RIP =(
Speaker Amp:Eclipse 4212
More photos here
Refs: trevor87, bumpin_blazer, jonny101abc
i believe the premier 860 can do it as well.

My Alpine CDA-9855 has it too.
EDIT: And if I would have read further up I would have seen the blanket "some Alpines" statement. Nice job noob.
Install Finished! Pics on my CarDomain site below.
Alpine CDA-9855 CD/MP3 Player
Audison LRx 1.400 Mono Amplifier (900x1)
Audison LRx 2.250 Stereo Amplifier (120x2)
MB Quart QM218.03 CX Components
Focal 33KX K2Power 13-inch Sub
Stinger Wiring
http://members.cardomain.com/demonboy0130

as far as i know it can't.....but if it can wanna tell me how to do it?Originally Posted by billybrown66
....i didn't know any pio units had this feature....some of them (p9...possible p1r) don't have an amp...but i dont 'know any that have an amp and can shut it off....
-jordan-
msn - jeby97@hotmail.com
aim - bumpinking
REFS -
rockingchair69
tirefryr
magick_man
cjj2d
ssj2xxgotenxx
Alpine 7998 is also without internal amp...more other goodies.
Headunit Alpine 9855
Front system: Caliber CCE 6 running on active setup, powered by Caliber 200V4
Subwoofer Caliber CWX 15" in 67l ported box, powered by Caliber 400V2
Condensor Caliber CAP 1IQN
Wired by Caliber
Bookmarks