Closed Thread
Results 1 to 2 of 2

Reload Thread: how do I run components, coaxials, and a sub?

  1. #1
    seankurz's Avatar
    seankurz is offline Junior Member



    Join Date
    Feb 2013
    Location
    Tempe, AZ
    Posts
    22
    Post Thanks / Like
    Mentioned
    0 Post(s)

    how do I run components, coaxials, and a sub?

    My head unit's manual only had diagrams for normal mode, 2 way mode, and 3 way mode, which I am attaching photos of. My question is how specifically do I run it the way I have it shown in the other picture?? With the complexity of systems today, I'm sure this is doable but I haven't found anything on how to so far, its been almost a day and a half of searching...

    I will be running a clarion cz702 head unit, an image dynamics CXT component set on an alpine MRX-F65, a matching CTX coaxial set off of an alpine MRP-F300, and a RF 210 sub off of a power acoustic amp (going to upgrade to RE sub/amp in trunk)

    How would I run this all out of the HU, specifically? do I need external hardware, or...?
    Attached Thumbnails Attached Thumbnails how do I run components, coaxials, and a sub?-how-.jpg   how do I run components, coaxials, and a sub?-f7177ae9-6704-49ac-a573-21b0f4c0bc62.jpg   how do I run components, coaxials, and a sub?-7604f3e7-0888-4f4c-ab45-7de3b39933cb.jpg   how do I run components, coaxials, and a sub?-5dc02768-1558-493a-b016-446e1799c931.jpg  







  2. #2
    seankurz's Avatar
    seankurz is offline Junior Member

    Threadstarter


    Join Date
    Feb 2013
    Location
    Tempe, AZ
    Posts
    22
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: how do I run components, coaxials, and a sub?

    i want to use the TA on the HU for the comps, but also keep the coax speakers and sub..
    would the setup i mentioned be okay or is there a better way to achieve what i want to do?
    HU rear rca outs>>>alpine MRX-F65>>>tweeters
    HU front rca outs>>>alpine MRX-F65>>>mids
    HU sub rca outs>>>fullrange signal>>>alpine MRP-F200>>>F300 rca outs>>>sub amp xover to filter out all but the lows.




Closed Thread

Similar Threads

  1. how can i run 4 speakers and a sub with only 2 sets of pre amp outputs?
    By SatisTraction in forum Wiring, Electrical and Installation Help
    Replies: 6
    Last Post: 08-04-2010, 05:48 PM
  2. How do I run RF PowerHX2 at 2ohms each?
    By ViCk-BuMp in forum Wiring, Electrical and Installation Help
    Replies: 11
    Last Post: 11-01-2002, 06:39 PM
  3. How do i run my amp power?
    By gunny86 in forum Wiring, Electrical and Installation Help
    Replies: 1
    Last Post: 08-23-2002, 07:03 PM
  4. help how do i run 3 kove's off a 2000 watt 2 hannel amp??
    By CaddyLacGrills in forum Amplifiers
    Replies: 0
    Last Post: 07-30-2002, 12:23 AM
  5. Replies: 1
    Last Post: 05-14-2002, 05:25 PM

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may post attachments
  • You may edit your posts
1e2 Forum