Printable View
Need an amp for a sub(s) and this is what will fit that I can find or know of, spot measures no more then 13"x 9.25"
JL XD600/1...400W @ 4ohms, 600W @ 2ohms $399
Alpine PDX-M6...600W @ 4ohms, 600W @ 2ohms $359
Boston GTA-800M...500W @ 4ohms, 800W @ 2ohms $299
PPI P1000.1...580W @ 4ohms, 725W @ 2ohms, 1000W @ 1ohm $239
Arc KS300.2...700W @ 4ohms bridged $369
Arc KS500.1...450W @ 4ohms, 600W @ 2ohms $469
Acr XDi 1000.1...650W @ 2ohms, 1150W @ 1ohm $299
Prices are from woofer btw...
Boston GTA, there down to one. Now go for it
The PPI is underrated and clean enough...that is my pick out of the bunch.
MMATS Amplifier Class D D1600.0 1ohm stable | eBay
here you go, american made 1150rms and one of the most effecient amps you can buy best deal for 300 out of any
WoofersEtc.com - D1600.1 - Mmats 1 Ch 1600 Watt Amplifier
msrp on them is 600 bucks
11x8 inches
arc for sure.
i was thinking arc
^^^^ this with out question, especially for that price, MMATS amps are monsters.Quote:
Originally Posted by mclerico83
1150 watts RMS on a 60 amp fuse at 13.8v...lol...I call bullshit, I don't care where it is made...It will need at least a 80a fuse. If it is even possible to be 100% efficient(which it is not), you are still only going to be able to pull 1035 rms through the 60a slow burn fuse and that is at 25% above the fuse rating...and let's just say our 60a fuse can handle +25% added current and the amp is 90% efficient (which It is still not), then you are looking at a max rms wattage of only 930 watts...but if you go by the Mmats website, they specifically state a max efficiency of 76% at full rated output...now we are down to a measely 787 watts rms.Quote:
Originally Posted by mclerico83
If you told me the Mmats D1600.1 amp is a 600 watt rms/1200 watt max at 1 ohm amp, then I would be inclined to believe you.
Boston GTA-800M...500W @ 4ohms, 800W @ 2ohms $299
^^^Gets my vote^^^^^^
if you never used one then dont comment. how does a cadence a7hc put out 1400rms clamped on 80 amps, fuses can handle double the power for small amounts of time. mmats is a highly regarded brand and quak you are the only person on this forum who wil lever doubt a mmats amp.Quote:
Originally Posted by quackhead
Signal to Noise Ratio >90dB
Low pass frequency crossover 35Hz~300Hz
Subsonic filter 10Hz~60Hz
Bass boost @ 45Hz 0~18dB
Phase shift control 0~180 degree
Frequency response 10Hz~350Hz (+/- 1dB)
T.H.D @ 4 ohm <0.1%
Efficiency @ 4 ohm 86%
Fuse rating 25A x 3
Input Sensitivity 200mV to 6V (+/- 5%)
Dimensions 252(W) x 58(H) x 294(L)mm
so quak how much power does this amp put out
MMATS Class D D1600.1
Specifications
D1600.1
STABLE TO: 1 ohm
SINE-WAVE POWER
@ 13.8 Volts:
Watts @ 1 ohms mono 1 X1600
Watts @ 2 ohms mono 1 X 900
RESISTIVE (RMS) POWER
@ 13.8 Volts:
Watts @ 1 ohms mono 1 X 1150
Watts @ 2 ohms mono 1 X 625
Idle Current: 1.5 amp
Signal to Noise Ratio A-Wtd: <85dB
Total Harmonic Distortion: 0.3%
Channel Separation: N/A
Input Sensitivity: 150mV-2.5V
Slew Rate: 13V / Usec
Fuse Rating: 60 amp
General Information:
Frequency Response: <10Hz to 275Hz
Low-pass Filter: Variable 24db, 77 to 275Hz
Battery Connectors: 2 Gauge
Speaker Connectors: 8 Gauge
MMats is too expensive...
Votes so far with other sites:
PPI - 3
Arc KS300 - 3
Boston - 2
JL - 1
Arc KS500 - 0
Arc XDi - 0
Alpine -0
^^^ this tooQuote:
Originally Posted by mclerico83
The MMats is too expensive...
From the list?
its 299 shipped brand new ??????Quote:
Originally Posted by perferd
MMATS Amplifier Class D D1600.0 1ohm stable | eBay