Closed Thread
Results 1 to 4 of 4

Reload Thread: removing Pioneer wiring harness

  1. #1
    maylar's Avatar
    maylar is offline Electrical Weenie



    Join Date
    Jan 2002
    Location
    Connecticut
    Age
    62
    Posts
    3,372
    Post Thanks / Like
    Mentioned
    13 Post(s)

    removing Pioneer wiring harness

    I have a Pioneer DEH-P6400 head unit and I can't figure out how to remove the damm wiring plug from the back. Pushed it in and it went "click", nice & snug. Now I need to get it out again. Don't see any ears or locking levers or anything to press in to get the plug to release. Is there a trick to this? Do I need some kinda frikkin tool or somethin?

    Grrrrr.



    dave
    ----------
    1999 Buick Park Ave Ultra
    Head Unit: JVC KWHDR720
    EQ: Audiocontrol EQL
    Front Stage: Hybrid Audio Technologies Imagine 5.25 mids, Morel Maximo tweets
    Sub Stage: Boston G3 10", 0.5 cu ft sealed
    Amp: PPI Phantom 900.4
    Rear Fill: Boston SE953 6X9's




  2. #2
    pioneer's Avatar
    pioneer is offline CarAudio.com Elite



    Join Date
    Mar 2002
    Location
    Trinidad & Tobago
    Age
    31
    Posts
    741
    Post Thanks / Like
    Mentioned
    0 Post(s)
    at the top center of the plug...there is supposed to be a small clip...i believe you suppose to take a small screw driver and gently press it down while pulling it out...do this very carefully...cuz i got frustrated with mine and i broke the clip...but no big harm cuz the plug still fits nice n snug...and you wont notice if the clip is broken off
    good luck



    why run with the crowd ?

    http://www.steveselectronics.biz - join the forum

  3. #3
    maylar's Avatar
    maylar is offline Electrical Weenie

    Threadstarter


    Join Date
    Jan 2002
    Location
    Connecticut
    Age
    62
    Posts
    3,372
    Post Thanks / Like
    Mentioned
    13 Post(s)
    Thanks man. They give ya this little poker thingie for a faceplate "tool", and special hooks for removing the HU from the sleeve... I was thinking maybe there's another fandangled special tool for the plug. I'll try a screwdriver.



    dave
    ----------
    1999 Buick Park Ave Ultra
    Head Unit: JVC KWHDR720
    EQ: Audiocontrol EQL
    Front Stage: Hybrid Audio Technologies Imagine 5.25 mids, Morel Maximo tweets
    Sub Stage: Boston G3 10", 0.5 cu ft sealed
    Amp: PPI Phantom 900.4
    Rear Fill: Boston SE953 6X9's

  4. #4
    pioneer's Avatar
    pioneer is offline CarAudio.com Elite



    Join Date
    Mar 2002
    Location
    Trinidad & Tobago
    Age
    31
    Posts
    741
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Icon14

    just remember to be VERY gentle with the screw driver...that clip snaps very easily...but if it does....the plug will still go in and stay



    why run with the crowd ?

    http://www.steveselectronics.biz - join the forum

Closed Thread

Similar Threads

  1. Pioneer Wiring harness Question: 9300 to a 9800BT
    By Accipiter in forum Head Units
    Replies: 2
    Last Post: 11-06-2010, 05:20 PM
  2. WTB Pioneer Wiring Harness
    By Silas871 in forum Wanting to Buy (WTB) - Car Audio
    Replies: 5
    Last Post: 06-13-2009, 03:09 PM
  3. WTB: Pioneer wiring harness'
    By MadLarkin in forum Wanting to Buy (WTB) - Car Audio
    Replies: 1
    Last Post: 11-29-2005, 11:02 AM

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may post attachments
  • You may edit your posts

1e2 Forum