Closed Thread
Results 1 to 2 of 2

Reload Thread: Alpine CDA-9887 Manual Posted

  1. #1
    genxx's Avatar
    genxx is offline Team JL Audio



    Join Date
    Mar 2007
    Location
    Oklahoma
    Posts
    1,170
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Alpine CDA-9887 Manual Posted

    Link was posted on another site. Did not see it here yet so check it out.

    It posted on here www.alpine-europe.com then click support and do a search and it will come up then just select the UK flag.

    Its 4.65MB so its pretty good sized if you are going to download it.



    2009 USACi Basic Consumer World Champion, '09 IASCA INAC 2nd Place, 2010 MECA Finals MODEX 4th, '10 OK MODEX State Champion--Addicted to Sound Quality
    '06 F250: JL-Zapco-Pioneer
    '08 Focus-Kenwood-Zapco-ID-Hertz
    Team JL Audio, Team RAAMmat, Team Advantage Audio, Team MSE, Team Zapco




  2. #2
    genxx's Avatar
    genxx is offline Team JL Audio

    Threadstarter


    Join Date
    Mar 2007
    Location
    Oklahoma
    Posts
    1,170
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Alpine CDA-9887 Manual Posted

    Props to Mach Y for all this info.


    Some info from the manual:

    When using MultEQ, MX, X-OVER, T.Correction, User’s EQ,
    Parametric EQ and Graphic EQ are set automatically. They are no
    longer user adjustable.

    Ok, that blows. Basically, if you use the Odyssey sound system to automatically level your car, you cannot tweak it AT ALL after that. To do any manual tweaking, the Odyssey MultEQ must be completely turned off

    If you do turn off MultEQ, you can do the following:

    7 band graphic eq, freqs are fixed:
    Band-1 (63 Hz) / Band-2 (150 Hz) / Band-3 (400 Hz) /
    Band-4 (1 kHz) / Band-5 (2.5 kHz) / Band-6 (6.3 kHz) /
    Band-7 (17.5 kHz)

    5 band para eq, freqs are adjustable in 1/3 octave increments for all 5 bands, from 20Hz to 20kHz, with +/-6dB on each, and a width of 1, 1.5, or 3.

    The crossover section can be set to:

    2.2ch (3WAY) System / L=R
    Setting items:
    LOW / MID-L / MID-H / HIGH

    2.2ch (3WAY) System / L /R
    Setting items:
    LOW-L / LOW-R / MID-L-L / MID-L-R / MID-H-L / MID-H-R /
    HIGH-L / HIGH-R

    Setting items:
    LOW / MID-L 20 Hz~200 Hz
    MID-H 20 Hz~20 kHz
    HIGH (1 kHz~20 kHz)

    Adjustable slope: FLAT, 6 dB/oct., 12 dB/oct., 18 dB/oct.,
    24 dB/oct

    Adjustable output level: –12 to 0 dB


    4.2ch (F/R/Sub-W) System / L=R
    Setting items:
    LOW / MID / HIGH

    4.2ch (F/R/Sub-W) System / L /R
    Setting items:
    LOW-L / LOW-R / MID-L / MID-R / HIGH-L / HIGH-R


    Time Delay goes from 0-99ms (0 - 132.7 inches)

    Specifications
    Tuning Range 87.5-108.0 MHz
    Mono Usable Sensitivity 0.7 μV
    Alternate Channel Selectivity 80 dB
    Signal-to-Noise Ratio 65 dB
    Stereo Separation 35 dB
    Capture Ratio 2.0 dB
    Tuning Range 531-1,602 kHz
    Sensitivity (IEC Standard) 25.1 μV/28 dB
    Tuning Range 153-281 kHz
    Sensitivity (IEC Standard) 31.6 μV/30 dB
    Frequency Response 5-20,000 Hz (1 dB)
    Wow & Flutter (% WRMS) Below measurable limits
    Total Harmonic Distortion 0.008% (at 1 kHz)
    Dynamic Range 95 dB (at 1 kHz)
    Signal-to-Noise Ratio 105 dB
    Channel Separation 85 dB (at 1 kHz)
    Wave length 795 nm
    Laser power CLASS I
    Power Requirement 14.4 V DC
    (11-16 V allowable)
    Maximum Power Output 60 W 4
    Maximum Pre-Output Voltage 4 V/10 k ohms
    Bass +20/–14 dB at 60 Hz
    Treble 14 dB at 10 kHz
    Weight 1.7 kg (3 lbs. 11 oz)



    2009 USACi Basic Consumer World Champion, '09 IASCA INAC 2nd Place, 2010 MECA Finals MODEX 4th, '10 OK MODEX State Champion--Addicted to Sound Quality
    '06 F250: JL-Zapco-Pioneer
    '08 Focus-Kenwood-Zapco-ID-Hertz
    Team JL Audio, Team RAAMmat, Team Advantage Audio, Team MSE, Team Zapco

Closed Thread

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may post attachments
  • You may edit your posts

1e2 Forum