Closed Thread
Results 1 to 7 of 7

Reload Thread: box plans, can someone please check this...

  1. #1
    graffix989's Avatar
    graffix989 is offline Member



    Join Date
    Oct 2004
    Location
    east coast
    Posts
    62
    Post Thanks / Like
    Images
    1
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    box plans, can someone please check this...

    this is the top view for two AW1206T Audiobans. going for 2.5 cu. ft. / port 4x7.25 per sub...
    the only thing i didnt quite understand was the port depth... how far should the walls of the ports go into the box. i guessed it would be the same width as the port opening on the outside. i also rounded off a couple numbers, the box should be just under 5 cu ft. ie 4.9 sumthin.. thats all my trunk will allow... would this work ok?? im shooting for about 36hz.. any suggestions would be great..



    the only reason i went with this style vs. the generic (subs right next to each other with the port to the side) was the structural integrety... i figured this would have more support in the middle than the other setup. but am i losing sound quality??
    Last edited by graffix989; 02-05-2005 at 07:51 PM.







  2. #2
    hello's Avatar
    hello is offline Junior Member



    Join Date
    Nov 2004
    Location
    S.E.A Land OF Hornbils
    Posts
    27
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Re: box plans, can someone please check this...

    I got the same problem with calculation from rouund port depth to slot. with the same sub.




  3. #3
    DBfan187's Avatar
    DBfan187 is offline Supa's mom was here!



    Join Date
    Jan 2003
    Location
    Poolside with Supa's mom.
    Posts
    46,452
    Post Thanks / Like
    Images
    12
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    11 Post(s)

    Re: box plans, can someone please check this...

    How ever wide your port is, it should be that wide from the back wall. You'll have to bend your port, L-shaped and add the end correction.




  4. #4
    graffix989's Avatar
    graffix989 is offline Member

    Threadstarter


    Join Date
    Oct 2004
    Location
    east coast
    Posts
    62
    Post Thanks / Like
    Images
    1
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Re: box plans, can someone please check this...

    soooo sumthin like the red... how about another one like the blue?? or is that too much. thats starting to rob my airspace isnt it?? is that even the correct way to do it??




  5. #5
    DBfan187's Avatar
    DBfan187 is offline Supa's mom was here!



    Join Date
    Jan 2003
    Location
    Poolside with Supa's mom.
    Posts
    46,452
    Post Thanks / Like
    Images
    12
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    11 Post(s)

    Re: box plans, can someone please check this...

    your port is 4.85" wide. So it needs to be 4.85" parallel from the wall, not 2.425". Keep it even, or it won't act right.




  6. #6
    graffix989's Avatar
    graffix989 is offline Member

    Threadstarter


    Join Date
    Oct 2004
    Location
    east coast
    Posts
    62
    Post Thanks / Like
    Images
    1
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Re: box plans, can someone please check this...

    so i dont combine the two?? see the 2.425x12 is the port size for one sub.... i made two seperate box designs an put em togethor (read it in one of george's post)
    in that case should i make the center channel 2.425 wide??




  7. #7
    DBfan187's Avatar
    DBfan187 is offline Supa's mom was here!



    Join Date
    Jan 2003
    Location
    Poolside with Supa's mom.
    Posts
    46,452
    Post Thanks / Like
    Images
    12
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    11 Post(s)

    Re: box plans, can someone please check this...

    n/m, sorry. you got it. I forgot that they were using there own port in the back. Looks good.




Closed Thread

Similar Threads

  1. I just finnished my box plans!!
    By flakko in forum Enclosure Design & Construction Help
    Replies: 20
    Last Post: 01-19-2005, 04:58 PM
  2. Box plans?
    By Zacmc212 in forum Enclosure Design & Construction Help
    Replies: 3
    Last Post: 10-27-2004, 05:28 PM
  3. ATTN: Jmac!
    By MUGEN! in forum General Discussion
    Replies: 4
    Last Post: 12-31-2002, 05:42 AM
  4. Replies: 2
    Last Post: 03-09-2002, 01:57 PM
  5. Box plans......
    By Scuba-Steve in forum Wiring, Electrical and Installation Help
    Replies: 0
    Last Post: 01-16-2002, 12:24 PM

User Tag List

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may post attachments
  • You may edit your posts
1e2 Forum