Closed Thread
Results 1 to 12 of 12

Reload Thread: how much round port for a 4^3 for a pair of xxx 12"

  1. #1
    plyhammer's Avatar
    plyhammer is offline Senior VIP Member



    Join Date
    Nov 2003
    Location
    ohio
    Age
    42
    Posts
    329
    Post Thanks / Like
    Images
    3
    Mentioned
    0 Post(s)

    how much round port for a 4^3 for a pair of xxx 12"

    I have a pair of 12" xxx in a 4^3 box. This is all going under the rear seat of a quad cab truck so it is as big as it is going to get. I have it braced with all thread to save cubes and it is straight on 4 cubes for the pair. I am having a little problem with the porting. The subs will have to downfire with the ports facing forward but I have checked with a couple of porting calculators and have gotten different answers from them. How much port do I need.







  2. #2
    pj_chevy03's Avatar
    pj_chevy03 is offline please ban me



    Join Date
    Jun 2004
    Location
    Alabama
    Posts
    921
    Post Thanks / Like
    Images
    7
    Mentioned
    0 Post(s)

    Re: how much round port for a 4^3 for a pair of xxx 12"

    jus seal em...2 12" xxx's i'm sure would be plenty loud sealed.. question, how tall are your back seats bottom seat cuz to fit those subs downfiring that would have to be a high back seat...u gotta have room for the huge magnet and then enuff room for the excursion...this doesnt seem likely





    Quote Originally Posted by unbonyr
    I just took it allitle to harsly I just sick of narrow-minded people

  3. #3
    plyhammer's Avatar
    plyhammer is offline Senior VIP Member

    Threadstarter


    Join Date
    Nov 2003
    Location
    ohio
    Age
    42
    Posts
    329
    Post Thanks / Like
    Images
    3
    Mentioned
    0 Post(s)

    Re: how much round port for a 4^3 for a pair of xxx 12"

    The subs are in the box already. I have the seat raised 5 inches to accomidate the extra room needed. Respl.com recommends 2.1 cubes per sub ported, I didn't think that I was too far off from that.




  4. #4
    helotaxi's Avatar
    helotaxi is offline Kilroy was Here



    Join Date
    Dec 2003
    Location
    South Central (New Mexico that is...)
    Age
    39
    Posts
    8,933
    Post Thanks / Like
    Images
    4
    Mentioned
    0 Post(s)

    Re: how much round port for a 4^3 for a pair of xxx 12"

    That 2.1 was effective air volume after considering the amount of air displaced by the subs themselves (.19 cu ft each) and any port volume within the enclosure. I am running 2 3" ports for a single XXX and the port displaces around .25 cu ft. You would need roughly twice the port area that I have and thus about twice the volume. After displacements you are looking at your 4 cu ft box being only about 3 cu ft and thus needing a longer port to get a good tuning freq. You are going to be better of with a sealed setup in that amount of space.



    Artificial Intelligence is no match for Natural Stupidity.

    Never underestimate the power of stupid people in large numbers.

    Life's tough...it's even tougher when you're stupid.

  5. #5
    plyhammer's Avatar
    plyhammer is offline Senior VIP Member

    Threadstarter


    Join Date
    Nov 2003
    Location
    ohio
    Age
    42
    Posts
    329
    Post Thanks / Like
    Images
    3
    Mentioned
    0 Post(s)

    Re: how much round port for a 4^3 for a pair of xxx 12"

    dang. What if the ports were external? Oh well, cant get bigger I will probably just have to seal it then. Thanks guys.




  6. #6
    plyhammer's Avatar
    plyhammer is offline Senior VIP Member

    Threadstarter


    Join Date
    Nov 2003
    Location
    ohio
    Age
    42
    Posts
    329
    Post Thanks / Like
    Images
    3
    Mentioned
    0 Post(s)

    Re: how much round port for a 4^3 for a pair of xxx 12"

    Should I cut some of the box to make it smaller then? I would have 3.6 cubes after sub displacement (thanks heli). Will 1.8 cubes per sub be too much sealed? thanks again




  7. #7
    helotaxi's Avatar
    helotaxi is offline Kilroy was Here



    Join Date
    Dec 2003
    Location
    South Central (New Mexico that is...)
    Age
    39
    Posts
    8,933
    Post Thanks / Like
    Images
    4
    Mentioned
    0 Post(s)

    Re: how much round port for a 4^3 for a pair of xxx 12"

    How much power are you running? It will probably sound a bit on the boomy side with that big an enclosure. If you already have it built, it can't hurt to give it a try before you cut it up to make it smaller.



    Artificial Intelligence is no match for Natural Stupidity.

    Never underestimate the power of stupid people in large numbers.

    Life's tough...it's even tougher when you're stupid.

  8. #8
    helotaxi's Avatar
    helotaxi is offline Kilroy was Here



    Join Date
    Dec 2003
    Location
    South Central (New Mexico that is...)
    Age
    39
    Posts
    8,933
    Post Thanks / Like
    Images
    4
    Mentioned
    0 Post(s)

    Re: how much round port for a 4^3 for a pair of xxx 12"

    When you don't run a ton of power to it, it isn't that big a deal. With 1kw it plots at 70ish mph port velocity within the usable frequency range. I don't have any audible noise.

    If your goal is SPL you need a huge amount of port area and a big box. The big box and high tune necessitate a lot of that port area. I'm in for SQ, smallish box, lower tune, lower power and smaller port area.



    Artificial Intelligence is no match for Natural Stupidity.

    Never underestimate the power of stupid people in large numbers.

    Life's tough...it's even tougher when you're stupid.

  9. #9
    helotaxi's Avatar
    helotaxi is offline Kilroy was Here



    Join Date
    Dec 2003
    Location
    South Central (New Mexico that is...)
    Age
    39
    Posts
    8,933
    Post Thanks / Like
    Images
    4
    Mentioned
    0 Post(s)

    Re: how much round port for a 4^3 for a pair of xxx 12"

    I was using Win ISD (and Pro I tried them both) and they both gave me the same result. Symetry of deisgn was important for me but not nearly as important as no port noise. I fiddled with the setup for a while during the modeling stage to make sure that it wouldn't be a problem. If I had gone to a bigger box I would have had issues. I should have the 250HCCA on it @ 1 ohm this afternoon, I'll let you know what happens.

    I have MSN messenger BTW. I just need to correct the setup.



    Artificial Intelligence is no match for Natural Stupidity.

    Never underestimate the power of stupid people in large numbers.

    Life's tough...it's even tougher when you're stupid.

  10. #10
    plyhammer's Avatar
    plyhammer is offline Senior VIP Member

    Threadstarter


    Join Date
    Nov 2003
    Location
    ohio
    Age
    42
    Posts
    329
    Post Thanks / Like
    Images
    3
    Mentioned
    0 Post(s)

    Re: how much round port for a 4^3 for a pair of xxx 12"

    1000-1500 watt apiece.




  11. #11
    helotaxi's Avatar
    helotaxi is offline Kilroy was Here



    Join Date
    Dec 2003
    Location
    South Central (New Mexico that is...)
    Age
    39
    Posts
    8,933
    Post Thanks / Like
    Images
    4
    Mentioned
    0 Post(s)

    Re: how much round port for a 4^3 for a pair of xxx 12"

    You'll want a smaller box.



    Artificial Intelligence is no match for Natural Stupidity.

    Never underestimate the power of stupid people in large numbers.

    Life's tough...it's even tougher when you're stupid.

  12. #12
    plyhammer's Avatar
    plyhammer is offline Senior VIP Member

    Threadstarter


    Join Date
    Nov 2003
    Location
    ohio
    Age
    42
    Posts
    329
    Post Thanks / Like
    Images
    3
    Mentioned
    0 Post(s)

    Re: how much round port for a 4^3 for a pair of xxx 12"

    can I put some wood inside of the box to reduce the airspace or do I need to rip the box apart to cut out some of the space?




Closed Thread

Similar Threads

  1. 12" Brahma or XXX? Spec by Spec / Myth by Myth
    By theimpaler in forum Subwoofers
    Replies: 22
    Last Post: 07-23-2004, 05:22 PM
  2. Round Port to Slot Port
    By TSL13505 in forum Enclosure Design & Construction Help
    Replies: 3
    Last Post: 06-18-2004, 07:10 PM
  3. People with the XXX 12"
    By BulldogSr04 in forum Subwoofers
    Replies: 1
    Last Post: 04-19-2004, 06:47 PM
  4. 12" XXX in an e46 BMW
    By hamann330ci in forum Subwoofers
    Replies: 7
    Last Post: 02-10-2004, 02:51 PM
  5. 15" XXX Sealed? or 12" XXX Ported?
    By Omarvelous in forum Enclosure Design & Construction Help
    Replies: 1
    Last Post: 01-18-2004, 02:50 PM

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may post attachments
  • You may edit your posts

1e2 Forum