+ Reply to Thread
Results 1 to 8 of 8

Reload Thread: Quieter Router bits for Jasper Jig?

  1. #1
    Bass911's Avatar
    Bass911 is offline CarAudio.com Elite



    Join Date
    Sep 2007
    Location
    Dallas,TX
    Posts
    1,050
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Icon32 Quieter Router bits for Jasper Jig?

    I was wondering if they make less noisy router bits. It is super loud when I'm cutting a circle. I heard Whiteside router bits make less noise? Jigsaw is quiet but I'd rather use the Jasper Jig. Any suggestions?







  2. #2
    Team Ampere's Avatar
    Team Ampere is offline Team Ampere Audio-Alabama



    Join Date
    Nov 2011
    Location
    birmingham,alabama
    Posts
    278
    Post Thanks / Like
    Mentioned
    8 Post(s)

    Re: Quieter Router bits for Jasper Jig?

    spiral upbit



    1997 Cadillac Seville
    30 cube Clamshell designed and installed by Neill Barber @ Audio Extremes
    6-Sundown ZV3 15"s d2....Sub Amps-AMPERE AUDIO 3800.1s
    Fiberglass Front Doors done by Me...6-Crescendo PWX 10s...6-Selenuim ST200s...Mids/Highs amps-AMPERE AUDIO 125.4s
    Head Unit-Pioneer 80prs
    Sky High 1/0, XS Power XP FLEX 8g
    Tenney 320a alt
    Batteries-Powerware Group 31s-(12 of them bastards)
    3" lift kit by Lift-a-brand.. 24" Verde Helix Rims

  3. Likes ciaonzo liked this post
  4. #3
    fasfocus00's Avatar
    fasfocus00 is online now doITdaWHITEwayORdoITtwice



    Join Date
    Jun 2007
    Location
    New Orleans, LA
    Posts
    5,355
    Post Thanks / Like
    Mentioned
    5 Post(s)

    Re: Quieter Router bits for Jasper Jig?

    noise is more related to the sharpness of the bit. if you notice that when you get a new bit it's usually quieter than your old bit. sounds like you just need a new bit. the higher end bits are usually more sharp than their cheaper counterparts.



    Here is my feedback Thread: http://www.caraudio.com/forum/showth...ght=fasfocus00

    "If you ain't cheatin', You ain't trying"

  5. Likes dumple liked this post
  6. #4
    ciaonzo's Avatar
    ciaonzo is offline TheContinental



    Join Date
    Feb 2009
    Location
    WI
    Age
    39
    Posts
    9,234
    Post Thanks / Like
    Mentioned
    33 Post(s)

    Re: Quieter Router bits for Jasper Jig?

    Quote Originally Posted by Team Ampere View Post
    spiral upbit
    Right on. Spiral upcut bit.

    Other than that, your bearings could be shot, that's usually pretty loud.



    Quote Originally Posted by audioholic View Post
    Saying "clipping doesn't kill speakers" is a half-truth at best. Technically no, clipping itself does not hurt the speaker. But in clipping your amp, you can easily create a situation that WILL kill the speaker. Was the squared waveform the DIRECT cause of the failure? No. In the end, the answer is, always has been, and can only be... heat kills speakers. BUT, clipping increases heat generation, sometimes by a drastic amount. So to start a thread simply to state that clipping does not hurt speakers is, again, a half-truth at best.

  7. #5
    Xrojas13's Avatar
    Xrojas13 is offline Senior VIP Member



    Join Date
    Aug 2012
    Location
    Palmetto fl
    Posts
    157
    Post Thanks / Like
    Mentioned
    1 Post(s)

    Re: Quieter Router bits for Jasper Jig?

    Disposable ear plugs



    1995 lincoln town car
    Front 4 crescendo pwx6 and 2 ap atx145 tweeters
    Middle 2 crescendo pwx6 and 2 ap atx 145 tweeters
    Rear deck 2 crescendo pwx6 and 2 ap atx 145 tweeters
    Center console 2 vfl's 8's
    Bk8004 - 8 crescendo 6's
    Bk8004 - four pm10's two pm8's two pm6's
    Bk1800.1d - 2 vfl's 8's at 1 ohm
    Bk340.4 - 8 atx145 tweeter s
    Bk340.4 - 4 selenium d250

  8. Likes speckdzl4shzl, ciaonzo liked this post
  9. #6
    Bass911's Avatar
    Bass911 is offline CarAudio.com Elite

    Threadstarter


    Join Date
    Sep 2007
    Location
    Dallas,TX
    Posts
    1,050
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: Quieter Router bits for Jasper Jig?

    Thanks. I'll try the upcut bit.




  10. #7
    bhsdriller's Avatar
    bhsdriller is offline CarAudio.com Veteran



    Join Date
    Jul 2007
    Location
    bakersfield,ca
    Posts
    4,491
    Post Thanks / Like
    Mentioned
    4 Post(s)

    Re: Quieter Router bits for Jasper Jig?

    yeah, when mine start to wear out they get louder



    Team Flex Issues
    4 18" Mayhems
    2 bc5500's


    Bought from: ameduce(x2), Hatchet_Warrior, jeeper07,DB_DRAG_SPL,ssackett, lyttleviet,MillzThaYungin, blackbonnie, ryan1126, Goindef154(x2), Lonnie, dave_damage

    Sold to: Ilovebass, nismos14, chednompton, teen, jonesy

  11. #8
    mlstrass's Avatar
    mlstrass is offline Shaggy DOA



    Join Date
    Jul 2006
    Location
    Illinois
    Posts
    10,445
    Post Thanks / Like
    Mentioned
    28 Post(s)

    Re: Quieter Router bits for Jasper Jig?

    x3 on spiral upcut bit and do 1/8" passes. Router speed might be too high, either way wear hearing protection as the high pitched noise isn't good for your ears...




+ Reply to Thread

Similar Threads

  1. Craftsman Professional Router with Bits and Jasper Jig
    By avs20 in forum Miscellaneous Classifieds
    Replies: 12
    Last Post: 07-14-2009, 12:05 AM
  2. Just bought a jasper jig, which router bits?
    By da box king in forum Enclosure Design & Construction Help
    Replies: 11
    Last Post: 03-03-2009, 04:01 AM
  3. ryobi plunge router and jasper jig and bit
    By 1loudsuv in forum Miscellaneous Classifieds
    Replies: 14
    Last Post: 09-25-2006, 11:13 AM
  4. for those with a router but no circle jig
    By joeldirt in forum Enclosure Design & Construction Help
    Replies: 11
    Last Post: 08-04-2005, 08:59 AM

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may post attachments
  • You may edit your posts

1e2 Forum