Closed Thread
Results 1 to 12 of 12

Reload Thread: box design SketchUp

  1. #1
    BoomBoxStereo's Avatar
    BoomBoxStereo is offline @woofergram



    Join Date
    Jul 2012
    Location
    Long Island, NY
    Posts
    1,801
    Post Thanks / Like
    Images
    6
    Mentioned
    13 Post(s)

    box design SketchUp

    i managed to whip this rough design up in SketchUp with the following dimensions given to me by @Better-Action ; thanks again for the help! if anyone would like to double check what i have going on here, please do! much appreciated!

    doubled up MDF to eliminate need for bracing (1.5 inch MDF except for inner port wall)
    top/bottom piece - 40" wide by 17" deep.
    right side - 17" high by 14" deep.
    left side (outer port wall) 17" high by 15.5" deep.
    front - 34.25" wide by 17" high.
    rear - 40" wide by 17" high

    the port is 17" high by 2.75" wide, 24 inches in total length. on the left (driver) side. it uses 3 common walls. it is tuned to 31.5hz with 11.5" of port per square foot.

    Last edited by BoomBoxStereo; 11-20-2012 at 11:39 AM.



    Two AA Mayhem motored 18's with SSA Zcon parts on 4k.

    Bought From: kickerassman, I Heart Vtec, dadydolas, gameovercca (x2), SPLaudio
    Sold To: Nopony7, 04murdalanche (x2), gameovercca




  2. #2
    BoomBoxStereo's Avatar
    BoomBoxStereo is offline @woofergram

    Threadstarter


    Join Date
    Jul 2012
    Location
    Long Island, NY
    Posts
    1,801
    Post Thanks / Like
    Images
    6
    Mentioned
    13 Post(s)

    Re: box design SketchUp

    anyone? @pro-rabbit ;



    Two AA Mayhem motored 18's with SSA Zcon parts on 4k.

    Bought From: kickerassman, I Heart Vtec, dadydolas, gameovercca (x2), SPLaudio
    Sold To: Nopony7, 04murdalanche (x2), gameovercca

  3. #3
    pro-rabbit's Avatar
    pro-rabbit is offline Moderator pro-rabbit is a Supporting Member of the forum!

    pro-rabbit is a Supporting Vendor of the forum!

    Join Date
    Jan 2004
    Location
    OKC, OK
    Age
    32
    Posts
    12,395
    Post Thanks / Like
    Mentioned
    373 Post(s)

    Re: box design SketchUp

    What are the actual H x W x D?

    That is a bit hard to follow or maybe it is just me.

    It does look like a box though, so good start I guess. I did read your email, and it was harder to follow then this. I don't agree with the full double baffle idea.




  4. #4
    Dirtrider4eva's Avatar
    Dirtrider4eva is offline √\_The CaUsE__



    Join Date
    Mar 2011
    Location
    Milwaukee, WI
    Posts
    4,289
    Post Thanks / Like
    Mentioned
    16 Post(s)

    Re: box design SketchUp

    is the first sub going to be interfering with the port? cant see on phone all that well.



    welcome to
    Where b-stock is the new a-stock
    TEAM WEST

  5. #5
    BoomBoxStereo's Avatar
    BoomBoxStereo is offline @woofergram

    Threadstarter


    Join Date
    Jul 2012
    Location
    Long Island, NY
    Posts
    1,801
    Post Thanks / Like
    Images
    6
    Mentioned
    13 Post(s)

    Re: box design SketchUp

    Quote Originally Posted by pro-rabbit View Post
    What are the actual H x W x D?

    That is a bit hard to follow or maybe it is just me.

    It does look like a box though, so good start I guess. I did read your email, and it was harder to follow then this. I don't agree with the full double baffle idea.
    total height - 1' 8"
    total width - 3' 4"
    total depth - 1' 5"



    Two AA Mayhem motored 18's with SSA Zcon parts on 4k.

    Bought From: kickerassman, I Heart Vtec, dadydolas, gameovercca (x2), SPLaudio
    Sold To: Nopony7, 04murdalanche (x2), gameovercca

  6. #6
    BoomBoxStereo's Avatar
    BoomBoxStereo is offline @woofergram

    Threadstarter


    Join Date
    Jul 2012
    Location
    Long Island, NY
    Posts
    1,801
    Post Thanks / Like
    Images
    6
    Mentioned
    13 Post(s)

    Re: box design SketchUp

    Quote Originally Posted by Dirtrider4eva View Post
    is the first sub going to be interfering with the port? cant see on phone all that well.
    it's a 24" port... 12.75" deep giving 2.75" clearance from the wall throughout. both subs are going to have to be shifted to the bottom right so they don't interfere with the port... is this okay?



    Two AA Mayhem motored 18's with SSA Zcon parts on 4k.

    Bought From: kickerassman, I Heart Vtec, dadydolas, gameovercca (x2), SPLaudio
    Sold To: Nopony7, 04murdalanche (x2), gameovercca

  7. #7
    Better-Action's Avatar
    Better-Action is offline give me a reach around



    Join Date
    Sep 2012
    Location
    SD
    Posts
    424
    Post Thanks / Like
    Mentioned
    4 Post(s)

    Re: box design SketchUp

    I recommended double baffle because it worked for the space he wanted to use and still has the Correct internal volume, and so he wouldn't have to brace. With the 45s, the port and the 1.5" thickness no bracing will be needed. Although I'm not about to argue with rabbit over a design, Guy knows his stuff.




  8. Thanks BoomBoxStereo thanked for this post
  9. #8
    BoomBoxStereo's Avatar
    BoomBoxStereo is offline @woofergram

    Threadstarter


    Join Date
    Jul 2012
    Location
    Long Island, NY
    Posts
    1,801
    Post Thanks / Like
    Images
    6
    Mentioned
    13 Post(s)

    Re: box design SketchUp

    @pro-rabbit ; recommendations?



    Two AA Mayhem motored 18's with SSA Zcon parts on 4k.

    Bought From: kickerassman, I Heart Vtec, dadydolas, gameovercca (x2), SPLaudio
    Sold To: Nopony7, 04murdalanche (x2), gameovercca

  10. #9
    BoomBoxStereo's Avatar
    BoomBoxStereo is offline @woofergram

    Threadstarter


    Join Date
    Jul 2012
    Location
    Long Island, NY
    Posts
    1,801
    Post Thanks / Like
    Images
    6
    Mentioned
    13 Post(s)

    Re: box design SketchUp

    HELP: say i wanted to use .75" MDF instead of doubling up on MDF... how would my dimensions change?



    Two AA Mayhem motored 18's with SSA Zcon parts on 4k.

    Bought From: kickerassman, I Heart Vtec, dadydolas, gameovercca (x2), SPLaudio
    Sold To: Nopony7, 04murdalanche (x2), gameovercca

  11. #10
    BoomBoxStereo's Avatar
    BoomBoxStereo is offline @woofergram

    Threadstarter


    Join Date
    Jul 2012
    Location
    Long Island, NY
    Posts
    1,801
    Post Thanks / Like
    Images
    6
    Mentioned
    13 Post(s)

    Re: box design SketchUp

    okay well the box is complete and sounds great!! @Better-Action ;







    (in the last photo it looks like theres a gap between the top plate and the rear wall, but there isn't. the top just overhangs a little bit. when i come back home from school in december i'm going to make it nice and flush and paint will be added. anybody have any cosmetic recommendations?



    Two AA Mayhem motored 18's with SSA Zcon parts on 4k.

    Bought From: kickerassman, I Heart Vtec, dadydolas, gameovercca (x2), SPLaudio
    Sold To: Nopony7, 04murdalanche (x2), gameovercca

  12. #11
    Better-Action's Avatar
    Better-Action is offline give me a reach around



    Join Date
    Sep 2012
    Location
    SD
    Posts
    424
    Post Thanks / Like
    Mentioned
    4 Post(s)

    Re: box design SketchUp

    You used the most recent cut sheet I sent you for .75"? Looks good for your first box, good work man. I'd recommended sanding the crap out of it. Get everything nice and smooth. Maybe paint it?




  13. Thanks BoomBoxStereo thanked for this post
    Likes BoomBoxStereo liked this post
  14. #12
    BoomBoxStereo's Avatar
    BoomBoxStereo is offline @woofergram

    Threadstarter


    Join Date
    Jul 2012
    Location
    Long Island, NY
    Posts
    1,801
    Post Thanks / Like
    Images
    6
    Mentioned
    13 Post(s)

    Re: box design SketchUp

    Quote Originally Posted by Better-Action View Post
    You used the most recent cut sheet I sent you for .75"? Looks good for your first box, good work man. I'd recommended sanding the crap out of it. Get everything nice and smooth. Maybe paint it?
    paint will definitely be added once i'm back home again



    Two AA Mayhem motored 18's with SSA Zcon parts on 4k.

    Bought From: kickerassman, I Heart Vtec, dadydolas, gameovercca (x2), SPLaudio
    Sold To: Nopony7, 04murdalanche (x2), gameovercca

Closed Thread

Similar Threads

  1. kinetik battery box design help! google sketchup
    By rcnshoe in forum Enclosure Design & Construction Help
    Replies: 0
    Last Post: 11-17-2007, 08:07 AM
  2. Replies: 11
    Last Post: 08-10-2007, 11:18 PM
  3. Help making box design with sketchup
    By CJL in forum Enclosure Design & Construction Help
    Replies: 30
    Last Post: 04-14-2006, 09:57 PM
  4. Anyone with Sketchup or box designing s'ware...could use your services.
    By JimJ in forum Enclosure Design & Construction Help
    Replies: 1
    Last Post: 09-18-2005, 04:43 PM
  5. sub box design questions
    By maylar in forum Wiring, Electrical and Installation Help
    Replies: 1
    Last Post: 01-15-2002, 03:00 PM

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may post attachments
  • You may edit your posts

1e2 Forum