Printable View
what: meca 2x event
when: saturday may 19th 10am-4pm
where: Shoppe's of Alum creek 1030 alum creek dr. columbus, OH 43209
who: YOU!
http://www.mecacaraudio.com/flyers/5-19-12OH.jpg
first event of a 4x weekend in columbus OH, get those points
and here's the rulebook for those not used to meca
http://www.mecacaraudio.com/2012rulebook.pdf
Question. I have a Hyundai 2 door hatchback and it has a reardeck/beauty panel thing that covers the hatch area but only snaps in and is completely removable. The relevant rules are as follows (for the street division)
So my question is, am I allowed to remove that piece for competing?Quote:
13. Rear deck must maintain factory appearance, have no holes and must have some type of upholstery/covering.
14. Modifications to the vehicle’s cargo area are limited to Non-Permanent Modifications. Cutting of metal is prohibited.
15. Any brackets, panels, 3rd row seats, and/or non-structural supports in the cargo area (behind the back seat and lower than
the top of the back seat) that can be unbolted or unscrewed may be removed, provided they can be reinstalled using factory fasteners and do not violate any other rules in section D.
It DOES sit lower than the back seats (by a few inches).
everything in my blazer is stock. everything in hatch is below back seat. what class would this put me in
I would say line 15 answers your question.Quote:
Originally Posted by bubbagumper6
It depends on your cone area and fusing before the amp.Quote:
Originally Posted by bgowdy31
Cone area is figured by the radius of your woofer/s squared times pi
Then you add amount of the fuse by your amp x 10
If you don't have a fuse within ~12in of your amp then it goes by the rms of your amp or one half of the peak or something like that.
somebody been studying the rulebook ;)Quote:
Originally Posted by kushy_dreams
AAAAAAAAAHHHH SHIIII you gonna come down from toleder to compete wif da meca boy and girls?Quote:
Originally Posted by bubbagumper6
AAAAAAAAAHHHH SHIIII you gonna come down from toleder to compete wif da meca boy and girls?Quote:
Originally Posted by bubbagumper6
Yeah, but I'm pretty sure when I asked on the MECA forum someone told me I had to leave it in, plus rule 13 kind of confused me as well...was just making sure :)Quote:
Originally Posted by kushy_dreams
EDIT: Nevermind I was thinking of a completely different post (Asked about dbdrag rules on termpro) I'm not even a member of the MECA forum lol
Moving to Columbus (Dublin) in May :)Quote:
Originally Posted by nateberrier
Also kind of depends on how small I can get my fusing....right now I'd be in Street 4, would be nice if I could get down to 3 or even 2....
I used to run a 40 amp on a 1500.1 mb quartQuote:
Originally Posted by bubbagumper6
You just get like a short burp before it blows? I'm running an SAZ-2500D and single 18". @kushy_dreams thought I may be able to get by with a 70A but I've got a 300A in there now, lulz.Quote:
Originally Posted by nateberrier
ok i have 1 18 hdc3 18. i believe i should be able to burp off of a 40a anl... were would that put meQuote:
Originally Posted by kushy_dreams
As2/s2/m2 depending on box orientation.Quote:
Originally Posted by bgowdy31
Fyi the 2500should be able to be burped off 70a of fusing with no issue
oh my box is below the top of back seat
---------- Post added at 07:14 AM ---------- Previous post was at 07:13 AM ----------
well my amp is only set for 2200
Will I pop the fuse everytime though? The cheapest I can find 70A ANL fuses is like $5 each so that's an expensive burp, haha. Might just have to invest in a different fuse holder for comps...Quote:
Originally Posted by thegreatestpenn
Do they make any kind of MINI ANL adapter that would fit inside a standard ANL fuse holder?
Quote:
Originally Posted by bubbagumper6
ive never heard of a mini anl adapter