Closed Thread
Results 1 to 9 of 9

Reload Thread: alarm installation

  1. #1
    Isuzu95's Avatar
    Isuzu95 is offline Member



    Join Date
    Dec 2002
    Location
    Toronto, Ontario
    Posts
    72
    Post Thanks / Like
    Mentioned
    0 Post(s)

    alarm installation

    I have a Clarion UNGO alarm which someone installed a while ago, and the wire for the dome light is not connected... so the dome light doesn't turn on when the alarm is disabled. The manual says that the dome light output is <-> negative so does that mean I connect it to the negative of the dome light or the positive?



    Pioneer DEH-P8400MP head unit,
    2 sets of Clarion 5-1/4" components SRS1353,
    3 - 12" Fosgate HX2 Subs,
    1 - Fosgate 1001 BD Power amp,
    1 - Fosgate Punch 501x 4 channel amp
    3 - Voodoo digital capacitors




  2. #2
    nismboy6986's Avatar
    nismboy6986 is offline the **** technician



    Join Date
    Jul 2002
    Location
    Belhaven NC
    Posts
    665
    Post Thanks / Like
    Mentioned
    0 Post(s)
    i'm not a expert but i'll probally say yes




  3. #3
    Isuzu95's Avatar
    Isuzu95 is offline Member

    Threadstarter


    Join Date
    Dec 2002
    Location
    Toronto, Ontario
    Posts
    72
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Originally posted by nismboy6986
    i'm not a expert but i'll probally say yes

    I appreciate the feedback, but it wasn't a 'yes-no' question... I was asking whether I should: (A) connect the negative wire from the alarm to the ground wire for the dome light OR (B) to the positive of the dome light.



    Pioneer DEH-P8400MP head unit,
    2 sets of Clarion 5-1/4" components SRS1353,
    3 - 12" Fosgate HX2 Subs,
    1 - Fosgate 1001 BD Power amp,
    1 - Fosgate Punch 501x 4 channel amp
    3 - Voodoo digital capacitors

  4. #4
    nismboy6986's Avatar
    nismboy6986 is offline the **** technician



    Join Date
    Jul 2002
    Location
    Belhaven NC
    Posts
    665
    Post Thanks / Like
    Mentioned
    0 Post(s)
    oh my bad i didn't read your question thoroughly.

    i believe you connect it to the negative but you would probally want more advice. on my alarm you need a relay and you connect terminal 86 to +12v terminal 87 to chassis ground and terminal 30 to negative dome light activation circuit.




  5. #5
    Isuzu95's Avatar
    Isuzu95 is offline Member

    Threadstarter


    Join Date
    Dec 2002
    Location
    Toronto, Ontario
    Posts
    72
    Post Thanks / Like
    Mentioned
    0 Post(s)
    no problem...


    and I'm not too familiar with terminal numbers... or if that's the way your alarm is setup... and/or if I would need a relay.. i'll just get it checked out at a shop or something.. thanks again



    Pioneer DEH-P8400MP head unit,
    2 sets of Clarion 5-1/4" components SRS1353,
    3 - 12" Fosgate HX2 Subs,
    1 - Fosgate 1001 BD Power amp,
    1 - Fosgate Punch 501x 4 channel amp
    3 - Voodoo digital capacitors

  6. #6
    Isuzu95's Avatar
    Isuzu95 is offline Member

    Threadstarter


    Join Date
    Dec 2002
    Location
    Toronto, Ontario
    Posts
    72
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Originally posted by Isuzu95
    no problem...


    and I'm not too familiar with terminal numbers... or if that's the way your alarm is setup... and/or if I would need a relay.. i'll just get it checked out at a shop or something.. thanks again
    also, the wiring diagram doesn't mention anything about terminal numbers so I wouldn't know how to set it up



    Pioneer DEH-P8400MP head unit,
    2 sets of Clarion 5-1/4" components SRS1353,
    3 - 12" Fosgate HX2 Subs,
    1 - Fosgate 1001 BD Power amp,
    1 - Fosgate Punch 501x 4 channel amp
    3 - Voodoo digital capacitors

  7. #7
    nismboy6986's Avatar
    nismboy6986 is offline the **** technician



    Join Date
    Jul 2002
    Location
    Belhaven NC
    Posts
    665
    Post Thanks / Like
    Mentioned
    0 Post(s)
    well i forgot to mention my alarm is crimestopper not a clarion UNGO. so u may or may not need a relay. for 4 dollars mrinstall.com will send you a instruction guide to wire a alarm to your specific vehicle. but if i were you i wouldn't just forget it and not worry about the done lights. i'm not going to attempt to hook them up when i install my alarm tomorrow since dome lights that come on when i disarm vehicle is no where near important enough to me to bother wiring them up




  8. #8
    Isuzu95's Avatar
    Isuzu95 is offline Member

    Threadstarter


    Join Date
    Dec 2002
    Location
    Toronto, Ontario
    Posts
    72
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Thanks, I'll check out that site. And I'm having the alarm re-installed completely because i'm having some problems with it, so i'll get it done then most likely... and if you have the features in your alarm, why not use it



    Pioneer DEH-P8400MP head unit,
    2 sets of Clarion 5-1/4" components SRS1353,
    3 - 12" Fosgate HX2 Subs,
    1 - Fosgate 1001 BD Power amp,
    1 - Fosgate Punch 501x 4 channel amp
    3 - Voodoo digital capacitors

  9. #9
    SentraStyle's Avatar
    SentraStyle is offline Senior VIP Member



    Join Date
    Dec 2002
    Location
    Kissimmee, Fl
    Posts
    464
    Post Thanks / Like
    Mentioned
    0 Post(s)
    What kind of car do you have...I can get you the wiring diagram for nothing...just send me an email.

    SentraStyleEMW@aol.com




Closed Thread

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may post attachments
  • You may edit your posts

1e2 Forum