Closed Thread
Page 1 of 5 1 2 3 4 5 LastLast
Results 1 to 15 of 75

Reload Thread: New project coming soon... possibly. Honduh

  1. #1
    Eugenics's Avatar
    Eugenics is offline Princess



    Join Date
    Jul 2005
    Location
    Arbys
    Posts
    23,904
    Post Thanks / Like
    Mentioned
    0 Post(s)

    New project coming soon... possibly. Honduh

    Not sure what chassis i'm going to go with. But i think i've determined what block i'll be going with.

    Was looking at a k20/k24... but meh.

    Thinking a H22, i'll be building it for upto 250fwhp n/a. Hopefully i'll be able to see a redline around 9k (around 200lbs of torque as well). I'll be happy with around 220whp, i just want a very fast/high revving engine. Although midrange torque is also a priority, gotta to pull me out of those twisties.

    Wont be cheap, but its something i can build up slowly with whatever money i have laying around. I might just run whatever engine the vehicle i decide on comes with while i build up the h block rather than pull it out constantly.

    Thinking i'll be running a B Series tranny.

    Should i go this route, the build will include resleeeeving, new pistons rods and crank, all balanced. Lots of headwork and all that funstuff. I'm getting antsy just thinking about it. I said i'd never do another FWD car again but i loved my accord so much, so meh.

    N/A FTW!!!

    Input/Conversation is welcome.



    crunktimes . com/ct




  2. #2
    spudracer326's Avatar
    spudracer326 is offline has a bastard system



    Join Date
    Jan 2006
    Location
    Oregon
    Age
    28
    Posts
    1,423
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: New project coming soon... possibly. Honduh

    put it in a four door integra(great chassis for handling, more so then the two door).....would be a sick canyon carver!! also dont throw out the k series so quick..that kinda build is spendy anyway you twist it...a k20a with cams/intake/exhaust/kpro will do better then the numbers your looking at witha fully built h22, and its not like swapping an h22 is much easier...just my 2cents




  3. #3
    azbass's Avatar
    azbass is offline the salty ca.com mod



    Join Date
    Sep 2004
    Location
    Long Beach, CA
    Posts
    34,922
    Post Thanks / Like
    Images
    6
    Mentioned
    0 Post(s)

    Re: New project coming soon... possibly. Honduh

    ugh why hondumb?




  4. #4
    DDeitz's Avatar
    DDeitz is offline CarAudio.com Veteran



    Join Date
    Sep 2006
    Location
    Winnipeg, Ca
    Posts
    2,020
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: New project coming soon... possibly. Honduh

    put it on a older gen prelude baby B18 200FWHP id say no shiategra since everyone and their mother owns one, if u could find a AE86 for cheap might be nice too oops didnt see the N\A part..




  5. #5
    Skip01's Avatar
    Skip01 is offline Diggy



    Join Date
    Apr 2006
    Location
    Marrero,LA
    Posts
    7,189
    Post Thanks / Like
    Mentioned
    1 Post(s)

    Re: New project coming soon... possibly. Honduh

    http://www.importreview.com/d_2.2.html

    220hp is nothin for a H22 really....no need to sleeve...unless ur boring out some more.

    Id go with a 4dr Civic....same weight basically as a HB but with 2 more doors...im bias though

    Good Luck....check out all motor section at www.honda-tech.com great info



    YOUTUBE VIDZ:

    http://www.youtube.com/user/Skip01

  6. #6
    Eugenics's Avatar
    Eugenics is offline Princess

    Threadstarter


    Join Date
    Jul 2005
    Location
    Arbys
    Posts
    23,904
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: New project coming soon... possibly. Honduh

    Quote Originally Posted by spudracer326 View Post
    put it in a four door integra(great chassis for handling, more so then the two door).....would be a sick canyon carver!! also dont throw out the k series so quick..that kinda build is spendy anyway you twist it...a k20a with cams/intake/exhaust/kpro will do better then the numbers your looking at witha fully built h22, and its not like swapping an h22 is much easier...just my 2cents
    Well if i decide to go with an accord or prelude it pretty much drops right in. Only really have to worry about obd and vtec wiring. Not a huge ordeal.

    Also there really is quite a lot involved in a K swap as far as fabrication is involved (although now there are kits for just about every car i'm sure). And the block itself is about 3k right off the bat isn't it? Even so the K might be a the best option. I know as far as a free revving engine its hard to beat.

    Quote Originally Posted by azbass View Post
    ugh why hondumb?
    I personally like the way they handle better, they're also easier to work on. And the aftermarket support for them is larger. I'll always like VW's. But as far as a project car to tinker with. It's hard to beat a hondumb.

    (not to mention i'm going n/a, which is not VW's forte)

    Quote Originally Posted by DDeitz View Post
    put it on a older gen prelude baby B18 200FWHP id say no shiategra since everyone and their mother owns one, if u could find a AE86 for cheap might be nice too oops didnt see the N\A part..
    Older preludes are a no go, and i really don't care for any of the B series engines except for the B18c5.... but those aren't easy to come by.

    and it HAS to be n/a. I know as far as power goes, turbo is cheaper. But i just love n/a motors. I've thought about getting an is300 sometime. If i go that route i will definitely go turbo.



    crunktimes . com/ct

  7. #7
    galacticmonkey's Avatar
    galacticmonkey is offline Wants a button like that.



    Join Date
    Sep 2006
    Location
    Tampa, FL
    Posts
    7,675
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: New project coming soon... possibly. Honduh

    You could always do it to a CRX and have a little sports car that will go decently fast and a nice little street setup with 1 12/2 10s.

    A friend had a CRX. Was a fun little car to drive. Just like a go kart!




  8. #8
    Eugenics's Avatar
    Eugenics is offline Princess

    Threadstarter


    Join Date
    Jul 2005
    Location
    Arbys
    Posts
    23,904
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: New project coming soon... possibly. Honduh

    I despise CRX's

    right now i'm thinking:
    94-95 2 door accord
    92-96 lude

    mayyyybe:
    94+ teg (meh)
    Civic hatch

    Not sure if the wheelbase is long enough though. Like spud said, if i go with an integra, it'll probably be a four door.



    crunktimes . com/ct

  9. #9
    Anonymous User's Avatar
    Anonymous User is offline ****** FTW!



    Join Date
    May 2005
    Location
    Bay Area, CA
    Posts
    2,110
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: New project coming soon... possibly. Honduh

    i say a 96-00 4dr civic with a k20a.

    i remember a few years back toda had a kit for the k20 that put the whp around near 240-250.. or you can do what super street did in there ep3, a k20a4 block w/ a k24 head.



    Car - 1995 Acura Integra LS/JDM Front
    Current System:
    Headunit - Alpine CDA-9853
    Speakers - Pioneer's front & rear
    Speaker Amp - Kenwood KAC-646x [not installed]
    Subs -none [not installed]
    Sub Amp - PA A3000DB [not installed]
    Enclosure - JL Audio Vantage 3 10" [not installed]
    Wiring - 4GA Kicker Hyperflex/Kun Kolossus Fleks/eKo RCA/Mini-ANL w/ 150A fuse
    Electrical - Optima Yellotop


    Official Feedback Thread

  10. #10
    Eugenics's Avatar
    Eugenics is offline Princess

    Threadstarter


    Join Date
    Jul 2005
    Location
    Arbys
    Posts
    23,904
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: New project coming soon... possibly. Honduh

    Quote Originally Posted by Skip01 View Post
    http://www.importreview.com/d_2.2.html

    220hp is nothin for a H22 really....no need to sleeve...unless ur boring out some more.

    Id go with a 4dr Civic....same weight basically as a HB but with 2 more doors...im bias though

    Good Luck....check out all motor section at www.honda-tech.com great info
    i've been a member of H-T since 04

    The only civic i would go with would be a hatch, and even there, i'm not so hot on that concept. The only reason i'm thinking about the hatch is weight. And a 4door civic would throw that out the window. Although they still are light.

    probably don't need to sleeve the H22 at 220whp, or 250 really. But i want to do it while the engine is torn apart anyway. along with some port/polishing action. wewt! I will probably be doing some boring work as well. Those composite sleeves can goto hell.



    crunktimes . com/ct

  11. #11
    spudracer326's Avatar
    spudracer326 is offline has a bastard system



    Join Date
    Jan 2006
    Location
    Oregon
    Age
    28
    Posts
    1,423
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: New project coming soon... possibly. Honduh

    k swaps can be had for cheaper just gotta look around/get lucky....I had a k24(tsx) with a blown Head/valvetrain(block was all i wanted, was planning k20a2 head swap) that I got rid of for basically nothing..if you had posted this a couple weeks ago before i sold the motor to a buddy, ida sold you the motor for what I paid plus shipping...wouldent of even been a grand(only paid 500 for the motor...ohh and yes the k swaps are quite involved...but the pain of swapping them is well worth it...




  12. #12
    Screnzo's Avatar
    Screnzo is offline What happened in here?



    Join Date
    Nov 2006
    Location
    Crunktimes
    Posts
    4,288
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: New project coming soon... possibly. Honduh

    If you go hatch, go with an 89-91 model....they tend to stand out a bit more...still had a kinda boxy look... I had one for the longest time, lightweight (for a hatch) and definetly a blast to drive.



    "you have a face like a bulldog chewing a stinging nettle while taking a constipated dump in a heat wave"

  13. #13
    Eugenics's Avatar
    Eugenics is offline Princess

    Threadstarter


    Join Date
    Jul 2005
    Location
    Arbys
    Posts
    23,904
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: New project coming soon... possibly. Honduh

    If i can get a K series that cheap i'll JUMP on it. any idea where i should look for situations/deals like yours?



    fap fap fap fap



    crunktimes . com/ct

  14. #14
    jmanpc's Avatar
    jmanpc is offline CA.com Nostalgist.



    Join Date
    Jan 2006
    Location
    Jacksonville, Fl
    Age
    26
    Posts
    17,265
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: New project coming soon... possibly. Honduh

    omg get a vtec prelude with a cold air intake and you'll run 10's easy.


    (according to my shithead friend)




    2007 Red Ford Focus ZX4 SE
    - Clarion DXZ955MC -
    - MB Quart RSD216 - 2 MB Quart RWE-354 in 4 cubic feet sealed -
    - MB Quart DSC4125 - Audiopipe AP1500.1D - Optima Blue Top -

    Team High Sexage

  15. #15
    Eugenics's Avatar
    Eugenics is offline Princess

    Threadstarter


    Join Date
    Jul 2005
    Location
    Arbys
    Posts
    23,904
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: New project coming soon... possibly. Honduh

    Quote Originally Posted by jmanpc View Post
    omg get a vtec prelude with a cold air intake and you'll run 10's easy.


    (according to my shithead friend)
    exhaust should put me into the 8's if i go that route.



    crunktimes . com/ct

Closed Thread
Page 1 of 5 1 2 3 4 5 LastLast

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may post attachments
  • You may edit your posts

1e2 Forum