+ Reply to Thread
Page 14 of 15 FirstFirst 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 LastLast
Results 196 to 210 of 224

Reload Thread: 2000 Blazer Build

  1. #196
    Join Date
    Nov 2011
    Location
    Dallas, Tx/Ada, Ok
    Age
    20
    Posts
    3,768
    Post Thanks / Like
    Mentioned
    32 Post(s)

    Re: 2000 Blazer Build

    Quote Originally Posted by treylittlefield View Post
    It being in the small size, smallish port, port close to hatch, those kida things lol clearance isn't the issue


    Also, does anyone know a admin on this site? I need my thread title changed lol
    Mods don't care enough to change it for you.. I've tried plenty times to ask







  2. #197
    treylittlefield's Avatar
    treylittlefield is offline CarAudio.com Elite

    Threadstarter


    Join Date
    May 2009
    Location
    Sand Rock, AL
    Posts
    1,421
    Post Thanks / Like
    Mentioned
    22 Post(s)

    Re: 2000 Blazer Build

    Quote Originally Posted by 04murdalanche View Post
    Mods don't care enough to change it for you.. I've tried plenty times to ask
    Imagine that. No surprise there lol



    I-Trader-http://www.caraudioclassifieds.org/forum/itrader.php?u=1860

  3. #198
    treylittlefield's Avatar
    treylittlefield is offline CarAudio.com Elite

    Threadstarter


    Join Date
    May 2009
    Location
    Sand Rock, AL
    Posts
    1,421
    Post Thanks / Like
    Mentioned
    22 Post(s)

    Re: 2000 Blazer Build

    Patiently waiting on wire. Still gotta install my alt bracket though. Been working on stuffing 3 batts in the back of this thing lol

    Here is a pic of where I plan on putting 2 of em.



    I had to cut out some of the inner skin to get it to fit good. Plan on wrapping the batt in a plastic bag and foaming under and behind the batt to help hold it in place.



    Tight but it fits that's looking inside the side panel beside the back seats.



    This was given to me a few weeks ago. Went out and shot it for the first time this past weekend.




    I-Trader-http://www.caraudioclassifieds.org/forum/itrader.php?u=1860

  4. #199
    treylittlefield's Avatar
    treylittlefield is offline CarAudio.com Elite

    Threadstarter


    Join Date
    May 2009
    Location
    Sand Rock, AL
    Posts
    1,421
    Post Thanks / Like
    Mentioned
    22 Post(s)

    Re: 2000 Blazer Build

    think i finally have my wiring and battery situation right.

    little bit of equipment to work with



    here is how the batts will be. will this work though? run alts to the front left battery shown, then to the right battery, then to the back battery, then to the amps? all the wire will be 4/0 welding cable.



    any input will be greatly appreciated, seems like the most logical way.



    I-Trader-http://www.caraudioclassifieds.org/forum/itrader.php?u=1860

  5. #200
    treylittlefield's Avatar
    treylittlefield is offline CarAudio.com Elite

    Threadstarter


    Join Date
    May 2009
    Location
    Sand Rock, AL
    Posts
    1,421
    Post Thanks / Like
    Mentioned
    22 Post(s)

    Re: 2000 Blazer Build

    Here are two ways I could go about wiring them.






    I went ahead and did it this way, if it doesn't work it won't be near as hard to change it.

    This will be where the two charge wires off the alts come to.



    Second batt



    3rd batt. Gonna need some terminals for this one. 1 4/0 3 1/0 and 2 gauge on each terminal. Will be 2 4/0 grounds running to frame off this batt also.



    Better idea of how it's ran. Still gotta put interior plastics back in.








    I-Trader-http://www.caraudioclassifieds.org/forum/itrader.php?u=1860

  6. #201
    Join Date
    Nov 2011
    Location
    Dallas, Tx/Ada, Ok
    Age
    20
    Posts
    3,768
    Post Thanks / Like
    Mentioned
    32 Post(s)

    Re: 2000 Blazer Build

    Niiiice




  7. #202
    treylittlefield's Avatar
    treylittlefield is offline CarAudio.com Elite

    Threadstarter


    Join Date
    May 2009
    Location
    Sand Rock, AL
    Posts
    1,421
    Post Thanks / Like
    Mentioned
    22 Post(s)

    Re: 2000 Blazer Build

    Quote Originally Posted by 04murdalanche View Post
    Niiiice
    Not much of an update. But I do what I can when I can lol



    I-Trader-http://www.caraudioclassifieds.org/forum/itrader.php?u=1860

  8. #203
    treylittlefield's Avatar
    treylittlefield is offline CarAudio.com Elite

    Threadstarter


    Join Date
    May 2009
    Location
    Sand Rock, AL
    Posts
    1,421
    Post Thanks / Like
    Mentioned
    22 Post(s)

    Re: 2000 Blazer Build

    Got a little bit of a problem i gotta fix first before i install the alts. See how the charging posts stick out? im afraid it is going to hit the hood and the power steering pump. (left alt is the top). gonna send it off to singer to get them re-clocked and possibly powder-coated if he will. might even get a clamp of them since Mechman was too lazy to do so.lol




    I-Trader-http://www.caraudioclassifieds.org/forum/itrader.php?u=1860

  9. #204
    treylittlefield's Avatar
    treylittlefield is offline CarAudio.com Elite

    Threadstarter


    Join Date
    May 2009
    Location
    Sand Rock, AL
    Posts
    1,421
    Post Thanks / Like
    Mentioned
    22 Post(s)

    Re: 2000 Blazer Build

    actually felt like i got a little bit acomplished today, was gonna send out the alts monday, but said screw it i'll test fit them even though i know they wont fit. i'll be damned if they fit lol

    doesnt hit the hood, not even the insulation inside the hood. was rather shocked





    here is where i had to beat the fender in a little so the bottom alt would fit right.




    little bit of sub ****




    this is the plan on securing the subs down




    Hopefullly this weekend i get the wires ran for the alts, get everything under the hood done except grounds. plan on getting subs mounted and amp installed besides the power and ground( waiting on a distro block from toolmaker). also plan to figure out the tuning i want and might play around with some polyfill to see how it effects it.



    I-Trader-http://www.caraudioclassifieds.org/forum/itrader.php?u=1860

  10. #205
    treylittlefield's Avatar
    treylittlefield is offline CarAudio.com Elite

    Threadstarter


    Join Date
    May 2009
    Location
    Sand Rock, AL
    Posts
    1,421
    Post Thanks / Like
    Mentioned
    22 Post(s)

    Re: 2000 Blazer Build

    Regulator wired up



    Had to fix this. Surprisingly it didn't sound all that bad like this lol


    Got the interior put back in for the most part


    Wiring up subs




    Oh yeah

    All mounted up. Gonna do some adjusting on the port and figure out tuning.



    With this I have 3 different port tunings, one without The middle, then two different middle sections. 9in,12in, and 16in iirc. Longest one should get me in the 20s



    Sending one of the alts off to singer to get clamped an powdercoated. When I get it back ill send the other one off.



    I-Trader-http://www.caraudioclassifieds.org/forum/itrader.php?u=1860

  11. #206
    Join Date
    Nov 2011
    Location
    Dallas, Tx/Ada, Ok
    Age
    20
    Posts
    3,768
    Post Thanks / Like
    Mentioned
    32 Post(s)

    Re: 2000 Blazer Build

    Getting close now!!




  12. #207
    quakerroatmeal's Avatar
    quakerroatmeal is offline CarAudio.com Elite



    Join Date
    Jan 2007
    Location
    Dallas, TX
    Posts
    1,429
    Post Thanks / Like
    Mentioned
    0 Post(s)

    Re: 2000 Blazer Build

    Holy smokes look at those surrounds. Those beast have some DSL surrounds. I've used those security screws + nuts before. Be very careful with them. I had problems before to where that bottom nut/teeth piece stripped underneath making it a BIG PITA to take the screw out.




  13. #208
    treylittlefield's Avatar
    treylittlefield is offline CarAudio.com Elite

    Threadstarter


    Join Date
    May 2009
    Location
    Sand Rock, AL
    Posts
    1,421
    Post Thanks / Like
    Mentioned
    22 Post(s)

    Re: 2000 Blazer Build

    Quote Originally Posted by quakerroatmeal View Post
    Holy smokes look at those surrounds. Those beast have some DSL surrounds. I've used those security screws + nuts before. Be very careful with them. I had problems before to where that bottom nut/teeth piece stripped underneath making it a BIG PITA to take the screw out.
    I've used them in a few boxes and figured out how to keep em in lol

    Quote Originally Posted by 04murdalanche View Post
    Getting close now!!
    **** right lol probably gonna run one alt for now and get em powdercoated one at a time.



    I-Trader-http://www.caraudioclassifieds.org/forum/itrader.php?u=1860

  14. #209
    treylittlefield's Avatar
    treylittlefield is offline CarAudio.com Elite

    Threadstarter


    Join Date
    May 2009
    Location
    Sand Rock, AL
    Posts
    1,421
    Post Thanks / Like
    Mentioned
    22 Post(s)

    Re: 2000 Blazer Build

    Went to the auburn/asu (I'm not an auburn fan, ROLL TIDE!!!)game tonight, but got a little done before the game and last night.

    Got my terminals from toolmaker.


    Wired up


    Alt belt ran for one alt while other is being powdercoated.




    2 grounds for my alts, just haven't hooked them up yet.



    4/0 cable cutters and crimpers. Life savers and have paid for themselves several times lol



    And anyone wanna guess what this means???




    I-Trader-http://www.caraudioclassifieds.org/forum/itrader.php?u=1860

  15. #210
    gckless's Avatar
    gckless is offline CarAudio.com Veteran



    Join Date
    Aug 2011
    Location
    San Antonio
    Posts
    3,973
    Post Thanks / Like
    Mentioned
    28 Post(s)

    Re: 2000 Blazer Build

    I don't wanna guess, but I'd like to know!



    Quote Originally Posted by ducatipaso View Post
    15inch subs can't play fast beats, they take more power and that taxes the vehicles electrical system. You will wake up and "hear" then see the light at the end of the tunnel and it will be 3 10's pounding so hard you wont even open your trunk or turn your system on because you 15's will sound sloppy & weak.
    Quote Originally Posted by benbenondatrack View Post
    stfu lesbo.why are you worried about me so much? you must want to date me ya little cookie monster but i dont even like sweets. your just a cup full of ice, dirt dead nasty azz ice...without the water.

    Dat Build Log: http://www.caraudio.com/forums/car-audio-build-logs-cars-trucks-suvs/578701-1999-chevrolet-blazer.html

+ Reply to Thread
Page 14 of 15 FirstFirst 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 LastLast

Similar Threads

  1. feeler.... 2000 blazer all hooked up FS
    By bobo244 in forum Miscellaneous Classifieds
    Replies: 9
    Last Post: 03-25-2006, 07:06 PM
  2. stock hu 2000 blazer
    By jtomsic in forum General Discussion
    Replies: 2
    Last Post: 03-24-2004, 07:38 PM
  3. 0/1 ga wire in my 2000 Blazer
    By smullen in forum Wiring, Electrical and Installation Help
    Replies: 1
    Last Post: 08-05-2003, 05:40 PM
  4. Mods for 2000 blazer vs. mods for 1996 non diesl yukon
    By Geminidj2000 in forum Car Interior/Exterior Enhancements
    Replies: 0
    Last Post: 03-21-2003, 11:22 PM

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may not post attachments
  • You may edit your posts

1e2 Forum