Closed Thread
Results 1 to 8 of 8

Reload Thread: Crossfire MB6 door pods (lots of pics)

  1. #1
    Perfectionist's Avatar
    Perfectionist is offline Junior Member



    Join Date
    Jun 2008
    Location
    South Africa
    Posts
    26
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Crossfire MB6 door pods (lots of pics)

    Thought i would document my build with photo's. Hope it helps someone out there. My good old faithful velocity's. Had these for about 8 years. They gave me some good service. This range of speaker by blauphunt was the first speaker that i know of that brought a dvc speaker. It was a 6x9 and man did i drive those things hard. Hard enough in fact to kill them about 3 years ago Door panel off Speaker removed. Door cleaned, waxed and ready for glass First layer of glass laid Second layer of glass done Rings cut First ring mounted with pregel to keep them in place and seal off all the gaps







  2. #2
    budahbuddy803's Avatar
    budahbuddy803 is offline CarAudio.com Veteran



    Join Date
    Feb 2006
    Location
    Clemson, SC
    Posts
    4,703
    Post Thanks / Like
    Images
    14
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    7 Post(s)

    Re: Crossfire MB6 door pods (lots of pics)

    i hope you throw some deadener on those doors.




  3. #3
    Perfectionist's Avatar
    Perfectionist is offline Junior Member

    Threadstarter


    Join Date
    Jun 2008
    Location
    South Africa
    Posts
    26
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Re: Crossfire MB6 door pods (lots of pics)

    Glass marked where i want to cut and then removed from the doors Top ring mounted at the angle that i needed. This was to try and get them to play as close to the center, top between the 2 front seats. Unfortunately the angle was way to much so i had to settle with a lot less Grills that i will be using Grills need some modification so here they are masked and ready for paint Painted and ready to be fitted




  4. #4
    stuckinok's Avatar
    stuckinok is offline Sick My Duck



    Join Date
    Jun 2006
    Location
    Rio Rancho, NM
    Posts
    5,258
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Re: Crossfire MB6 door pods (lots of pics)

    looking good



    Team High Desert Mobile Electronics ABQ, NM

  5. #5
    Perfectionist's Avatar
    Perfectionist is offline Junior Member

    Threadstarter


    Join Date
    Jun 2008
    Location
    South Africa
    Posts
    26
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Re: Crossfire MB6 door pods (lots of pics)

    oops made a mistake and had to remove the door molded piece from the rings in order to stretch the cloth over the rings without any creases Cloth pulled over rings, clued to the bottom and then resigned. If anyone decides to do this make sure that the resign doesn't go anywhere near the glue otherwise it will come lose. To avoid this i placed the pods upside down on top of something. Pods ground and ready for body filler or as you guys would call it bondo i think. Body filler added and then flattened with a sanding block to make it look smooth and straight Filler boards cut and filed to fit flush with door panel and ready for trimming




  6. #6
    Perfectionist's Avatar
    Perfectionist is offline Junior Member

    Threadstarter


    Join Date
    Jun 2008
    Location
    South Africa
    Posts
    26
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Re: Crossfire MB6 door pods (lots of pics)

    Sorry forgot to take photo's before i mounted them. Here's the completed work. With and without flash Now the car need to go for a serious clean inside




  7. #7
    Rashaddd's Avatar
    Rashaddd is offline Terrrrrist



    Join Date
    May 2008
    Location
    Sacramento
    Posts
    5,095
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Re: Crossfire MB6 door pods (lots of pics)

    Nice work man those look great




    Refs: themommyvan, CharlieAnderson, bassknocker23, bigbirney420, wu501, _JaY_, lrc131, R/T Pimp, NeverEnuffBass, d-REW, slapmaster, headbussaboi, edzy, adio, 1ndatrunk, jfink, k_schutte, bigredhybrid, ARSkemp, s-saudio, pimpdaddyq, AudioFreak, scarolinablazin, ssackett, kylebechtold, craigzter, etc..................

  8. #8
    andrewmoore13's Avatar
    andrewmoore13 is offline CarAudio.com Veteran



    Join Date
    Oct 2007
    Location
    Gloucester, MA
    Age
    27
    Posts
    2,188
    Post Thanks / Like
    Images
    5
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Re: Crossfire MB6 door pods (lots of pics)

    thats pretty sweet. i like the LEDs



    HU: Alpine iVA-w505
    Processor: Alpine PXA-H701
    Front Doors: Shok Comps
    AMP Speakers: Diamond Audio D7104
    AMP Subs: American Bass VFL 150.1 gold
    Subs: 2 Custom Sundown Z12s. Dual 2
    Kicker 1/0 wire (soon to be Shok 1/0)
    Stinger SPV44 and a XS Power 5100

    refs: http://www.caraudio.com/forum/showthread.php?p=5007514#post5007514

Closed Thread

User Tag List

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may not post attachments
  • You may edit your posts
1e2 Forum