PDA

View Full Version : is this a good speaker setup??(budget)



traksta15
05-09-2005, 12:42 AM
ok, i drive a 90 camaro and i can't fit kicks in the floor boards because i'm 6'3" and need all the space i can get.....so i'll just have to put speakers in the stock locations. so here's what i wanted to do.........

Infinity 4x6 plate speakers http://www.ikesound.com/product-product_id/1343
should i amp these with this amp http://www.profilecaraudio.com/amplifiers.htm
(the 100sx btw) or just run them off the HU?(pioneer deh-4600mp) if i don't amp them, i'll use the amp for some 6.5's in the rear. I know its not good to have your main midbass behind you , but i'm afraid i won't have any midbass at all (besides the dash infinities) without some rear fill........so for some 6.5's i was thinkin about these.....
pioneer 6.5 coaxials http://www.ikesound.com/product-product_id/2942
OR
alpine 6.5 type s coaxials http://www.ikesound.com/product-product_id/1292

both will be amped with the profile 100sx, any help would be greatly appreciated and i know the best solution would be to get comps and put them in some kicks, but i don't have the know how, or space for them........TIA

zachzchw
05-09-2005, 12:47 AM
I had some infinity plates running off deck power, I was quite impressed, especially for the price.

traksta15
05-09-2005, 12:51 AM
thanks for the input, im just worried that i won't be able to find some speakers that can keep up with my subs......on a budget.

traksta15
05-10-2005, 12:19 AM
bump.......

iLL-Faded
05-11-2005, 12:02 AM
2 Rockford Fosgate T1462C (4"x6" 2-way Speakers) = $55
Power Handling (RMS) - 40 watts

Power Handling (Peak) - 80 watts

Frequency Response - 80-22k hz


2 Rockford Fosgate T152C (5-1/4" 2-way Speakers) = $65
Power Handling (RMS) - 60 watts

Power Handling (Peak) - 120 watts

Frequency Response - 70-22k hz


hit me up with a pm if your interested

traksta15
05-11-2005, 12:06 AM
are those used or new??how do they sound?i might be interested, but everyone around here runs runs RF........

iLL-Faded
05-11-2005, 12:08 AM
used, but in good condition, the installer, installed them and i never took them out, had them in for like 2 months, good SQ better then my card board stock speakers

iLL-Faded
05-11-2005, 12:10 AM
i have the original box for the front speakers(4x6) with all the screws and everything

Slody4Futbol
05-11-2005, 12:17 AM
are you SURE you can't fit kicks?! is it an automatic or stick? if it's an auto you can fit some fiberglass kicks in... i did and i'm 6'2"... i had a 91 camaro a few years ago... the 4x6 plates will NOT fit unless you heat and remold the a/c vents and cut away some plastic... i tried...

iLL-Faded
05-11-2005, 12:29 AM
you could angle the 4x6 which i did, i only used 2 screws

Slody4Futbol
05-11-2005, 12:36 AM
and if it's a plate... then more than likely the rubber surround of the mid will hit the bulky camaro dash... i hated that sound... so i returned them bought some components... and got some fiberglass kicks made

traksta15
05-11-2005, 01:10 AM
its an automatic. I might be able to fit them, but i have no experience in glassing, nor do i want to pay $200+ for qlogic kicks.......what should i do?i had a thread about maybe making some sort of a "minibox" for my comps to fit in the kick area....it would have the same effect as a set of kicks, just not the curvacious look of most kicks.........any thoughts???

Slody4Futbol
05-11-2005, 01:11 AM
www.thirdgen.org was the forum i was a member of... i ordered my kicks from them... covered in black tweed... very nice...

Trancer
05-11-2005, 05:32 PM
I have the Infinity Kappa 4x6 plates and they are amazing. A 3 inch cone and a half inch suprised me. I ran mine off an amp and they got loud. They are rated at 65 rms. I was pushing a little more to them than that.

traksta15
05-11-2005, 10:56 PM
slody4futbol, where on thirdgen.org did you buy them?

Slody4Futbol
05-11-2005, 11:26 PM
there was a guy named rezn8r ... that was a few years ago... and someone sold the molds to another guy... just do a search for fiberglass kicks or fiberglass kick panels... or make a post to see who makes some now

traksta15
05-12-2005, 12:32 AM
how much were they? if you dont mind me askin????