View Full Version : How do i waterproof my 6.5" speakers?

04-07-2005, 01:04 AM
i just switched out my DA M661 components for DA Hex's. i noticed there were water marks on the back of the 6.5" midbass. when i mount the 6.5" in the door, there isnt anything to protect the speaker from water. so everytime it rains, my speakers will get wet. is there anyway to safely water proof them? maybe partially wrap them in plastic or make a shroud?

04-07-2005, 01:06 AM
Get some foam baffles. Or you can always look into some marine speakers, which are meant for boats :rolleyes:

04-07-2005, 01:07 AM
build some kick panels for em

04-07-2005, 10:41 AM
Send me your M6's

04-07-2005, 10:57 AM
Buy the foam baffels, or bass boxes. And cut out the back portion. Unless you park on a slant this should protect the speaker. You could also silicon up the wire connection to be safe.

04-08-2005, 02:23 AM
WOW, i never knew such things like this existed. exactly what i was looking for, thank you!!!!!

if i use these baffles, itll wrap around the entire back portion of the speaker, would this affect the sound quality of the 6.5" speakers? doesnt the 6.5" midrange/midbass need an open back area to perform right?

04-08-2005, 02:34 AM
The vast majority of speakers are created with an infinite baffle (free air) setup in mind. Some say that the use of a foam baffle, acting somewhat like a very small, sealed eclosure, actually improved the midrange/bass response. But this depends on your install & speakers, YMMV. If you liked the sound they created before the baffles, you could always cut out the backs like stated above. :D

04-08-2005, 02:45 AM
what does YMMV mean? doesnt the 6.5" speaker need open air to function correctly? i notice on my diamond components, there a whole on the back of the magnet and a mesh screen deep inside.

04-08-2005, 02:48 AM
YMMV = Your mileage may vary & no it doesn't need open air to function correctly. If this was the case anyone who has their speakers in kick panels or fiberglassed in their door panels would not be very pleased.

04-08-2005, 10:13 AM
Some speakers are designed to perform best infinite baffle (no box). Some speakers will still perform decently well in an enclosure. If you are really that worried about it, just cut a large hole in the bottom of the baffle; Viola, you're back to being infinite baffle with the speakers.

no it doesn't need open air to function correctly. If this was the case anyone who has their speakers in kick panels or fiberglassed in their door panels would not be very pleased.

It is possible to put the speakers in kickpanels and end up with undesireable results ;) Just depends on the speaker being used. Some speakers will need to be vented into and open area (like into the inner fender well) when in kicks to perform optimally

04-08-2005, 10:22 AM
note. as cj said

cut a hole in the back of the foam

DO NOT cut a hole in the 'back'

rain is falling from above, so like squeak said, cut a hole BELOW the magnet on the back side... like this VVV


and for future refrence squeak... im not a photoshop queen :bawling: so please dont put that in your sig or call me that... it makes me cry.

04-08-2005, 11:16 AM

You know I <3 you req ;)

04-08-2005, 11:46 AM
you better ;)

dont you love my idiotic photoshop skills?

04-08-2005, 05:51 PM
im going to do exactly that. thanks REQ!

04-08-2005, 05:53 PM
Try it sealed first though, just incase there is an improvement.

04-10-2005, 08:11 PM
you could also try making an aperiodic enclosure:


04-11-2005, 12:27 AM
The local shop here that deals DA suggests not running diamond comps in sealed baffles but cutting a hole in the bottom. They advised me to do the same to my cdt's